Keypad When the phone is being charged whilst it is switched off, is it normal for the c key, activity menu key, and 3 key to illuminate orange whilst all other keys remain dark? Do I need to take my new phone back?

Keypad lock:

1. To lock the keypad press Menu then Star (*) key.
2. To unlock the keypad press Unlock (Menu key) then Star (*).

Telephone: Fax: VAT Registration No.:
Infrared remote control
NOTE: Infrared emitter can be seen at front edge of key.
System operation
Switch ignition ON. Ensure clock LED illuminates for 3-5 seconds. Pressing key lock button once activates central locking and alarm. Pressing key lock button twice within 3 seconds activates double locking system.
Programming
When
Key batteries completely discharged. Key batteries not replaced within 15 seconds. Key added or replaced. System malfunction.
How
Obtain all keys fitted with remote control. Turn ignition switch to position I. Wait approximately 10 seconds. Ensure clock LED illuminates.
NOTE: LED illuminates for approximately 5 seconds.
Switch ignition OFF and remove key, while LED illuminated. Programming mode activated for approximately 20 seconds (LED illuminated). Proceed as follows: Point key at receiver (located near interior lamp). Press and hold unlock button Fig. 1 [1]. After approximately 1 second key LED will flash once [3]. Press lock button 3 times Fig. 1 [2]. Release unlock button Fig. 1 [1]. Continue to point key at receiver until LEDs in clock and key have flashed 5 times. Ensure LED remains illuminated. Repeat above procedure within 20 seconds to program remaining keys. To exit programming mode and extinguish clock LED: Switch ignition ON and OFF. Wait approximately 20 seconds.
NOTE: A maximum of 4 keys can be programmed. Fig. 1
Radio frequency remote control
System operation
Switch ignition ON. Ensure clock LED illuminates for 3-5 seconds.


Pressing tailgate release button twice within 3 seconds unlocks the tailgate - if fitted. Pressing key lock button once activates central locking and alarm. Pressing key lock button twice within 3 seconds activates double locking system. Interior lamp illuminates when disarming system.
Programming
When
Key added or replaced. System malfunction.
How
Obtain all keys fitted with remote control. Fasten seat belts and close all doors. From position I, turn ignition switch as follows: To position II. To position I. To position II. To position I. To position II. To position I. Programming mode activated for approximately 20 seconds. LED or fog lamps ON warning lamp illuminates (some models) or the system will emit an acoustic signal to indicate start of programming mode. Proceed as follows: Type 1: Press and hold unlock button Fig. 1 [1]. Type 2: Press unlock button Fig. 2 [2]. Ensure clock LED or fog lamps ON warning lamp flashes (some models) or wait for acoustic signal (indicates correct programming). Wait 2 seconds. Repeat above procedure within 20 seconds to program remaining keys. To exit programming mode: Switch ignition ON. Wait 20 seconds.
NOTE: A maximum of 4 keys can be programmed.

Switch-off your phone. 1. Press and hold 3
keys; Green dial key, *
Star key, no. 3 key on keypad and then press
the power on/off to
swtich on the phone. Remember, do not let go the 3
press and hold
keys until you see a formatting word screen show! 2.
After a few
minutes when the Full phone formatting completed, your phone
will
back to original system and factory settting.

Hi

please help calculation
my sn: 13191

thx

The driver door module (DDM) is connected on the standard corporate protocol (SCP) communication network. The DDM controls many functions including power windows, power door locks and remote keyless entry. The DDM also communicates with the driver seat module (DSM) to control the power mirror and seat memory functions.
Do you know anything about automotive electronic control modules ?
The driver door module (DDM) receives inputs from the digital transmission range (DTR) sensor, ignition switch, seat switch, window/door lock switches, lighting control module (LCM), keyless entry keypad switch and remote transmitter. The DDM outputs consists of keyless entry keypad switch illumination, power door lock actuators, luggage compartment release solenoid, horn relay, and lighting control module (LCM).
Best thing to do would be to have a factory scan tool hooked up to check for DTC'S diagnostic trouble codes . That should be the first step if it's not programming the code.

• The doors do not lock/unlock using the keyless entry keypad

• Keypad.
• Circuitry.
• Driver door module (DDM).

• GO to Pinpoint Test L .

PINPOINT TEST L: THE DOORS DO NOT LOCK/UNLOCK USING THE KEYLESS ENTRY KEYPAD CONDITIONS DETAILS/RESULTS/ACTIONS L1 RETRIEVE THE RECORDED RESULTS FROM BOTH CONTINUOUS AND ON DEMAND SELF TESTS Use the recorded DDM DTCs from the Continuous and On Demand self tests.

• Are any DTCs recorded?

Yes For DTC B1525, GO to L3 .

For all other DDM DTCs, REFER to the DDM Diagnostic Trouble Code (DTC) Index.

No If the door locks are inoperative, GO to L2 .

If the keypad illumination does not operate, GO to L10 .

If the keypad illumination is on continuously, GO to L14 .
L2 CHECK THE DOOR LOCK OPERATION Check the door lock operation by depressing a door lock switch.

• Do the door locks operate?

Yes GO to L3 .

No GO to Pinpoint Test E . L3 MONITOR THE DDM PID KEY_PAD
Scan tool
Monitor the DDM PID KEY_PAD.

• Are any of the keyless entry keypad switch numbers present?

Yes GO to L4 .

No GO to L5 . L4 CHECK THE KEYLESS ENTRY KEYPAD SWITCH
Keyless Entry Keypad Switch C525
Monitor the DDM PID KEY_PAD.

• Are any of the keyless entry keypad switch numbers present?

Yes If 1/2, REPAIR Circuit 78 (LB/YE). TEST the system for normal operation.
If 3/4, REPAIR Circuit 79 (LG/RD). TEST the system for normal operation.
If 5/6, REPAIR Circuit 121 (YE/BK). TEST the system for normal operation.
If 7/8, REPAIR Circuit 122 (YE). TEST the system for normal operation.
If 9/0, REPAIR Circuit 123 (RD). TEST the system for normal operation.

No INSTALL a new keyless entry keypad switch; for additional information, REFER to Keypad-Keyless Entry . L5 CHECK THE KEYLESS ENTRY KEYPAD INPUT WITH THE KEYLESS ENTRY KEYPAD SWITCH Monitor the DDM PID KEY_PAD, while depressing all the keyless entry keypad switches one at a time.

• Are all the keyless entry keypad switches operating correctly?

Yes GO to L9 .

No GO to L6 . L6 CHECK CIRCUIT 797 (LG/VT) FOR VOLTAGE
Keyless Entry Keypad C525
Measure the voltage between keyless entry keypad C525-7, Circuit 797 (LG/VT), and ground; and between keyless entry keypad C525-8, Circuit 797 (LG/VT), and ground.

• Are the voltages greater than 10 volts?

Yes GO to L7 .

No REPAIR Circuit 797 (LG/VT). TEST the system for normal operation. L7 CHECK THE KEYLESS ENTRY KEYPAD SWITCH INPUT While monitoring the DDM PID KEY_PAD, momentarily connect a fused (7.5A) jumper wire between positive battery post and keyless entry keypad switch C525 as follows:

Keypad Button Keyless Keypad Switch C525 Circuit 1/2 Pin 3 78 (LB/YE) 3/4 Pin 4 79 (LG/RD) 5/6 Pin 5 121 (YE/BK) 7/8 Pin 6 122 (YE) 9/0 Pin 1 123 (RD)

• Are all the keyless entry keypad switch inputs operating correctly?

Yes INSTALL a new keyless entry keypad switch; for additional information, REFER to Keypad-Keyless Entry .

No GO to L8 . L8 CHECK THE KEYLESS ENTRY KEYPAD SWITCH CIRCUITRY FOR AN OPEN
DDM
Measure the resistance between keyless entry keypad switch C525 and DDM as follows:

Keyless Keypad Switch C525 DDM Circuit Pin 3 C521 Pin 8 78 (LB/YE) Pin 4 C521 Pin 13 79 (LG/RD) Pin 5 C521 Pin 16 121 (YE/BK) Pin 6 C520 Pin 24 122 (YE) Pin 1 C520 Pin 25 123 (RD)

• Is the resistance less than 5 ohms?

Yes INSTALL a new DDM; for additional information, REFER to Section 419-10 . TEST the system for normal operation.

No REPAIR the circuit in question. TEST the system for normal operation. L9 CHECK THE KEYLESS ENTRY KEYPAD BACKLIGHT Depress a key on the keyless entry keypad.

• Does the keypad illumination operate correctly?

Yes INSTALL a new DDM. For additional information, REFER to Section 419-10 . TEST the system for normal operation.

No If the keypad illumination does not operate, GO to L10 .

If the keypad illumination is on continuously, GO to L14 . L10 CHECK THE KEYPAD - DDM ACTIVE COMMAND KEYPAD BACKLIGHTING LIGHT ON AND OFF Trigger the DDM active command KEYPAD BACKLIGHTING LIGHT ON and OFF.

• Does the keypad illumination turn off and on?

Yes INSTALL a new DDM. For additional information, REFER to Section 419-10 . TEST the system for normal operation.

No GO to L11 . L11 CHECK DDM GROUND - JUMPER CIRCUIT 66 (LB) TO GROUND
DDM 522
Connect a fused (7.5A) jumper wire between DDM C522-4, circuit 66 (LB), and ground.

• Does the keypad illuminate?

Yes INSTALL a new DDM; for additional information, REFER to Section 419-10 . TEST the system for normal operation.

No GO to L12 . L12 CHECK CIRCUIT 51 (BK/W) FOR OPEN
Keyless Entry Keypad C525
Measure the voltage between keyless entry keypad C525-7, circuit 797 (LG/VT), and ground; and between keyless entry keypad C525-8, circuit 797 (LG/VT), and ground.

• Are the voltages greater than 10 volts?

Yes GO to L13 .

No REPAIR circuit 797 (LG/VT). TEST the system for normal operation. L13 CHECK CIRCUIT 66 (LB) FOR OPEN Measure the resistance between keyless entry keypad C525-2, Circuit 66 (LB), and DDM C522-4, Circuit 66, (LB).

• Is the resistance less than 5 ohms?

Yes INSTALL a new keyless entry keypad switch; for additional information, REFER to Keypad-Keyless Entry .

No REPAIR Circuit 66 (LB). TEST the system for normal operation. L14 CHECK THE KEYPAD ILLUMINATION - DDM DISCONNECTED
DDM C522

• Does the keypad illumination turn off?

Yes INSTALL a new DDM; for additional information, REFER to Section 419-10 . TEST the system for normal operation.

No GO to L15 . L15 CHECK KEYLESS ENTRY KEYPAD FOR SHORT TO GROUND
Keyless Entry Keypad C525

• Does the keypad illumination turn off?

Yes GO to L16 .

No INSTALL a new keyless entry keypad switch. For additional information, REFER to Keypad-Keyless Entry . TEST the system for normal operation. L16 CHECK CIRCUIT 66 (LB) FOR SHORT TO GROUND Measure resistance between DDM C522-4, circuit 66 (LB), and ground.

• Is resistance greater than 10,000 ohms?

Yes System OK. CLARIFY the concern with the customer.

No REPAIR circuit 66 (LB). TEST the system for normal operation.

The steps are outlined in the article below:

D900 FAQ – How do I disable or mute the keypad tone on my SGH-D900? admin ⋅ March 6, 2009 --> Note: In order to disable the keypad tone, the Dialing Display Font Type must first be set to “Normal”
To change the dialing display font type follow the steps below:

1. From the standby screen, press the left soft key for Menu
2. Select Settings (9)
3. Select Display Settings (3)
4. Select Dialing Display (6)
5. Select Font Type (1)
6. Highlight either Normal or Theme, using the navigation keys
7. Press the left soft key to Save the Dialing Display Font Type setting

To turn off the keypad tone follow the steps below:

1. From the standby screen, press the left soft key for Menu
2. Select Settings (9)
3. Select Sound Settings (4)
4. Select Keypad Tone (2)
5. Highlight Off, using the up navigation key
6. Press the left soft key to Save the Keypad Tone setting

You can manually lock the keypad to avoid pressing keys by accident. You can still answer an incoming call and the keypad will lock again when the call is finished. The keypad remains locked until you unlock it manually.
Depending on your phone model, you can activate the automatic keylock. When the automatic keylock is activated, the keypad locks shortly after you stop pressing keys.
Please note: with some phones you can still use external keys when the keypad is locked. If you wish to lock the external keys you must lock them separately.

K530i To manually lock the keypad:

1. From standby, press the * key.
2. Select 'Lock keys'.

To activate automatic keylock:

1. From standby, select 'Menu' > Settings.
2. In the General (tab), select Security.
3. Select Automatic keylock > On.

To unlock the keypad:

1. From standby, press the * key.
2. Select 'Unlock'.

You can manually lock the keypad to avoid pressing keys by accident. You can still answer an incoming call and the keypad will lock again when the call is finished. The keypad remains locked until you unlock it manually.
Depending on your phone model, you can activate the automatic keylock. When the automatic keylock is activated, the keypad locks shortly after you stop pressing keys.
Please note: with some phones you can still use external keys when the keypad is locked. If you wish to lock the external keys you must lock them separately.

K800i To manually lock the keypad:

1. From standby, press the * key.
2. Select "Lock keys".

To activate automatic keylock:

1. From standby, select "Menu" > Settings.
2. In the General (tab), select Security.
3. Select Automatic keylock > On.

To unlock the keypad:

1. From standby, press the * key.
2. Select "Unlock".
3. hope this helps Thanks and God bless

Try bootloader mode. Hold down the * and # key at the same time, then press the power key. (3 keys all together). You should get a bootloader menu. If you do, your phone can be saved. If not...

The default security code for Nokia is 12345.
Try this:
Take your SIM card out.
Make sure your phone battery is fully charged.
Press * 3 send at the same time and turn the phone on. Keep them pressed until the reset screen appears.
Give it time to reset.
Yes! I know. You need someone to press the ON button.