No Audio output from 410

It sounds like you may be experiencing a configuration issue with your M-Audio FireWire 410 audio interface. Here are a few steps you can try to troubleshoot the issue:

1. Check the connections: Make sure that the FireWire 410 is securely connected to your computer and that all cables are properly plugged in. If the connections are loose or faulty, it can cause problems with the audio output.
2. Restart the device: Sometimes, restarting the audio interface can resolve issues with the audio output. To do this, disconnect the FireWire 410 from your computer, wait a few seconds, and then reconnect it.
3. Update the drivers: It is possible that the drivers for your FireWire 410 may be out of date or incompatible with your operating system. To update the drivers, visit the M-Audio website and download the latest drivers for your device. Once the drivers are installed, restart your computer and try using the FireWire 410 again.
4. Check the settings: Make sure that the FireWire 410 is selected as the default audio device in your operating system's audio settings. You can access these settings by going to Control Panel > Hardware and Sound > Sound. Under the Playback and Recording tabs, select the FireWire 410 and click the Set Default button.

If these steps do not resolve the issue, it is best to contact M-Audio support for further assistance. They should be able to provide you with specific guidance for troubleshooting the problem with your FireWire 410.

printer offline means disconnected or turned off.
did you try to check if its selected as default to your computer?.
1, check device and printer of your computer and make your printer default,
2, use the usb cord of the printer first, so you could use your printer and configure it to wifi setup.

No,your old tv used analog outputs,the new one is didital output...horst in aussy land..

This statement is too much to bare anybody. Please do not disturb us anymore.

re install the mac drivers from mfg web sight

poop
no format
reset the device google it

Hi isterix!
I also have a 410 on a acer 1502 laptop with xp. I installed the latest driver (5.10.00.5053) and i have sound (after changing sound preferences in panel control) but it makes me peaks in the playback. I think it's due to the driver, that is the same also for windows vista. I'll try to install the previous one and i'll tell you!

Hello have you disabled all the built on sound cards on your computers? This is a known problem. If you are going to use a great product like M-audio disable any onboard audio card. Then try to use the 410 system. If you still have the problem try changing the latency to 4-5

You must be running on pc, or it sounds like you may have a ground loop issue. If you are running a mac, then bus power over the firewire should be enough. If your running on a pc, try getting a pcmcia card with 6 pin firewire ports. If not then your pc laptop will have to power the 410 via ac adapter. That means both should be plugged in tot he wall. Ive gotten that interference before, and gett it on any audio, whether im producing or playing itunes. I find the trick is to reset the 410 via the output window in the top right. It's right above the level knob. Also, try just installing the latest driver, with the 410 disconnected, then launch it from a different file path than the icon.

I still use it for the macbook pro, and its not always top notch. I bought it 3 years ago for 500, and i see what 500 buys nowadays.......MOTU!!!!

Keep me posted.

You should install service pack 2, the go to the m-audio site and upgrade the drivers again. Also, since your computer most likely have a 4 pin firewire, make sure you have the power cqble for the 410 connected. Ofcourse, do not have the 410 connected when upgrade either sp2 or the drivers. make sure you power cycle both devices before reconnecting and attempting to record....

http://www.m-audio.com/index.php?do=support&tab=driver&serie_ID=2&PID=5f35def5b4107998b11119907053a313&OS=15

keep me posted...