Erasing some or all stored numbers from memory

Hi yusef_13,

The problem you encountered happen when your phone memory or memory card is full.

A. I suggest to you first, try deleting or erasing some of your stored messages.

B. Second, Also try erasing file or moving them to MMC location.

C. Third, you can also restore the phone factory settings, by going to settings and select restore or reset factory setting, but before doing that, be sure to BACK-UP all your needed data.


Hope it helps.

Thank You for using Fixya.

1.Press the FOLDER button to choose a folder.
Every time the FOLDER button is pressed, it cycles through folders and the List display will appear (+P20).

2 Press the + or – button to choose the file you want to erase.

3 Press the ERASE button. The “Cancel” indicator flashes.

4 Press the + button to choose “Erase”.

5 Press the OK button. The display changes to “File Erase!” and erasing will start. “Erase Done” is displayed when the file is erased. File numbers will be reassigned automatically

try first deleting or erasing some of your stored messages, example sent items or inbox old items.
you can also try erasing received file or moving them to the mmc location.
also you can restore the phone factory settings, by going to settings and select restore or reset factory setting, but before doing that, be sure to BACKUP all your needed data.

Programming
memory buttons
External autodial
1. If you are on a call or an open line with dial tone, press Hold
or Rls
2. Press Feature * 1
3. Press a memory button.
4. Dial the external number.
5. Press Hold to store the number.
6. Label your new button.

Internal autodial
1. If you are on a call or an open line with dial tone, press Hold
or Rls
2. Press Feature * 2
3. Press a memory button.
4. Dial the internal number.
5. Label your new button.

Features
1. If you are on a call or an open line with dial tone, press Hold
or Rls
2. Press Feature * 3
3. Press a memory button.
4. Press Feature and the feature code.
5. Label your new button.

Erasing memory buttons
1. If you are on a call or an open line with dial tone, press Hold
or Rls
2. Press Feature * 1
3. Press the memory button you want to erase.
4. Press Hold to erase the button.

Before you store a telephone number in memory, make sure the dialing mode is
correctly set for the type of service you have. The default dialing mode is tone
(touch-tone), so if you have pulse (rotary) service, you must first change the dialing
mode. See “To Set the Dial Mode.” The following buttons can be stored into any
memory location: 0-9.
STORING FREQUENTLY CALLED NUMBERS
1. Pick up the handset.
2.Press the store button.
3. Push the desired memory location button.
4. Press the store button.
5.Use the handset number keys to enter the telephone number (up to 16-digits)
and press the store button.
6.Hang up the handset.
NOTE: If you make a mistake, use the delete button to delete wrong digits.
CHANGING A STORED NUMBER
Repeat the storage sequence above. The new number replaces the old number at
the memory location.
ERASING A STORED NUMBER
1. Pick up the handset.
2.Press the store button.
3.Press the memory location (0-9) to be erased.
4.Press delete for three seconds until the number in the display is erased.
5.Hang up the handset.
DIALING FREQUENTLY CALLED NUMBERS
1. Pick up the handset and press the mem button.
2. Press 0-9 for the memory location. The number dials automatically.
OR
1. Pick up the handset and press the dial button.
2. Press the review button for the desired memory location.
3. Press the dial button to dial the number.
OR
1. Press dial button while the handset is still in the cradle.
2. Press the review button for the desired memory location, lift the handset and the
number dials automatically.

Download User Manual

If this information was helpful, please give me a big thumbs-up when you rate my answer. Thank you.

go to the call register and try erasing them there.

My Mom had this same problem.   I found these instructions on Uniden's website (uniden.com) under the "Owner Manuel" section.


Here you go - good luck!








Using the Speed Dial Memory 
Storing Numbers in Speed Dial Memory 
Your cordless phone can store up to ten numbers (up to 20 digits each) in the speed dial 
memory. To store number in memory: 
1) When the phone is in standby, press [memory]. The talk/batt low LED flashes. 
2) Use the keypad to enter the phone number. 
 (To enter a 2-second pause between numbers, press [redial/ 
pause]. Each pause counts as a digit. ) 
3) Press [memory] again. 
4) Select the speed dial location where you would like to store the 
number ( [0] to [9] ). You will hear a confirmation tone indicating 
that the number has been stored. 
NOTE: 
• Storing a number to a speed dial location will 
overwrite the any previously stored number without 
warning. 
• When storing numbers into memory and the handset is idle (i.e., no key is 
pressed) for more than 0 seconds, it will beep rapidly, and then the phone 
will return to standby. 
Dialing a Stored Number 
1) When the phone is in standby, press [talk], and listen for a dial tone. 
2) Press [memory] and enter the speed dial entry ([0] – [9]) that has the stored number 
you want to dial. (If you enter a digit that does not contain a stored number, the 
handset will beep rapidly, and the phone will not dial.) 
Chain Dialing 
The speed dial memory is not limited to phone numbers. You can store any number (up 
to 20 digits) that you need to enter once your call connects. This is referred to as Chain 
Dialing. An example is a frequently refilled prescription number. Store your pharmacy 
phone number in one speed dial and your most frequently refilled prescription number 
as another speed dial. To use, once you ring your pharmacy's automated prescription 
line, simply press [memory] and the speed dial number where you stored your account 
number. 
Erasing a Stored Number from Memory 
1) With the phone in standby, press [memory] twice. 
2) Press the number of the speed dial entry. A tone indicates that the stored number is 
erased from memory. 

It takes a lot of patience; however pursue an AT&T telephone number that is manned by a live person; then follow a trail of phone numbers until one of them connects with a helpfull live person who is familiar with the problem and who then furnishes a very simple solution.

no!!!!!!!!! brother tech

FROM THE MANUAL


ERASE MEMORY

Erase memory erases your Phonebook and Voice Dial recordings. This feature is useful if you want to give your phone to a friend or family member.

1. In standby mode, press the left soft key (Menu), then press 9 (Setup), 4 (Security). You're prompted to enter the lock code.

2. Enter the lock code (try the last 4 digits of your phone number unless you set a different one), then press 6 for Erase Memory. A confirmation prompt appears in the display.

3. Use the navigation key to highlight Yes or No, then press OK. A confirmation message appears in the display while your messages are being erased. Your phone then returns to the Security menu.


RESET PHONE

Reset Phone returns all setup options to their factory default.

1. In standby mode, press the left soft key (Menu) then press 9 (Setup), 4 (Security). You're prompted to enter your lock code.

2. Enter the lock code, then press 7 for Reset Phone. A prompt appears in the display asking if you wish to restore default settings (except for the Phonebook and Voice Dial).

3. Use the navigation key to highlight Yes or No, then press OK.