E 3 error what does this indicate? - AEG 23 in. 6410KF-N Electric Cooktop

Error code 22 on a Defy Slimline hob usually indicates an issue with the touch control panel or power supply. Here are a few steps you can try to resolve the issue:

1. Turn off the power to the hob at the circuit breaker for a few minutes, and then turn it back on. This can reset the electronics in the hob and clear the error.
2. Check the hob's power supply. Make sure the hob is getting power from the electrical outlet or circuit breaker. If the hob is plugged in, try plugging it into a different outlet or resetting the circuit breaker.
3. Check the touch control panel. Sometimes, the error code can be caused by a problem with the touch control panel. Make sure the panel is clean and free of debris or moisture. If the panel is damaged, it may need to be replaced.
4. Contact a qualified technician. If the above steps don't resolve the issue, it may be a more serious problem with the hob's electronics or power supply. Contact a qualified technician or the manufacturer for further assistance.

The 'H' symbols will flash in the display the first time your hob is connected and switched on. This is because the hob has been heat tested at the factory, then switched off while still hot. This may also happen if you are using the hob and you have a power cut.

Error code F1 indicates that the power is too low due to unsuitable cookware or an empty pot. Error code F indicates that there is no cookware on the zone or the cookware is unsuitable.

..

• Error code E13 error showing on display
• What causes an E13, E 13 error code on the Induction Cooktop control panel?
• Error code 13 on Induction Cooktop control panel

Cause:

• Universal OFF key failure

Troubleshooting:

1. If the controls are wet or water made contact with them, dry off the controls.
2. Turn off then back on to reset.
3. If the error persists, reset the unit at the circuit breaker.
4. Turn the unit back on to see if the error code cleared.

The induction cooktop will flash "F" when cookware has been removed from the surface; cookware is not present when the unit is turned on; or cookware is not centered on the element.
Position the cookware properly over the center of the cooking surface if the error code "F" flashes. Use only induction cookware and use a bigger pan, as the error code "F" indicates that the pan is too small for the cooking element.

Hi Dolores, I understand that your cooktop will not turn on after receiving an error code "40". Usually this error code can indicate a communication error between the Induction Module, Relay Board, and Control Board. I would also recommend doing a hard reset by unplugging or turning the household power breaker off to the appliance for five to ten minutes. If the problem persists, please reach out to a professional technician. Hope this helps! -JK

A quick web search of "Error code 35 induction cooktop" seems to indicate a possible bad control board in the unit, but you would need to get more specific about the make/model of the unit to know for sure. A Google search should help you find the answer but that seems to be the most common one and mostly relating to Kenmore units.

Hello Robert - Typically, error code E95 indicates a power voltage miscommunication to the main components of the unit. You may try and reset the induction cook top by disconnecting the power to the unit for up to 30 seconds by flipping the circuit breaker off and back on. This often clears most false error codes. If the error code does not clear, then I would recommend contacting a professional to proceed further.

F1 indicates a clock or touch pad problem. F8 indicates a clock, or ERC (Electronic Range Control) problem. Are you receiving both codes? If so it seems likely that your touch pad and ERC are contained together in one module, and must be replaced. If you find however that they are separate modules it is possible to determine which is faulty by simply disconnecting power to the unit, disconnecting the touch pad from the ERC, and then powering it back up. Wait for a half hour or so to see if the unit sets the error code again with the touch pad disconnected. If it does the ERC is faulty, otherwise it is the touch pad.

Please note that if you do not have experience mucking about in your appliances inner workings it is best that this be done by an experienced technician.

Hi


Thanks for using FixYa. Error F 1-7 in your Maytag indicates keypad disconnected. To start with check the wiring between the keypad and Electronic Range control (ERC), if still the issue is not resolved then you’ll have to replace the keypad. Please do rate the solution if the issue is resolved or post a comment for further assistance.


Thanks
Rylee