Was receiving E68 code on Frigidaire GLEQ2152ES1, replaced circuit board and am still receiving the e68 error code. What else will cause this error?

E68 for this model number says in manual that this is for a "button stuck" or held down for more than 30 seconds

ck all your buttons for one that just doesn't "feel right" when its pressed , this one will be your problem

Good Afternoon David,

I understand that your Frigidaire Affinity dryer, model# LEQ6000ES2, is showing you an error code of E68 and will not start. I also see that you have changed the thermal limiter. Looking at what the E68 error code means, a key or button stuck, there could be something else causing the code to come up. I suggest contacting your local authorized technician for further assistance. They will be able to diagnose your appliance, determine what is causing the E68, and repair your dryer. Hope this is helpful.

-Best Regards-
WP

Good Morning Friend,

I understand you want to know how to replace the board on your Frigidaire dryer, model# GLEQ2152ES, due to receiving an E68 code. Typically, this is not a do it yourself repair, as there are no step by step instruction manuals. I suggest contacting your local authorized technician for further assistance. They have been trained on your particular appliance, and should be able to replace the board with ease. Hope this is helpful.

-Best Regards-
WP

Good Morning Gary,

I understand you are receiving an E68 code on your Frigidaire Affinity washer, model# ATF7000E. The E68 code states that there is a current leak to the ground on the heater or there is a fuse open. This could also be a false error code. I suggest resetting your appliance, by either unplugging it or shutting the power off at the circuit breaker, for 3-5 minutes. Restore power and start any cycle. I ask that you please follow up with a comment on the post, at your convenience, to advise if further troubleshooting is needed or if your appliances status has changed successfully. Hope this is helpful.

-Best Regards-
WP

Good Afternoon Friend,

I understand you are receiving an E68 error code on your Frigidaire Affinity washer, model# ATF7000E. The E68 error code states that there is a possibility something is going on with the heating element inside your washer. It could also be a false error code. I suggest resetting your appliance, by either unplugging it or shutting the power off at your home's circuit breaker, for 3-5 minutes. Restore power and start your washer on the hottest cycle on a heavy soil level. I ask that you please follow up with a comment on the post, at your convenience, to advise if further troubleshooting is needed or if your washer status has changed successfully. Hope this is helpful.

-Best Regards-
WP

Good Morning Mua_m7,

I see that you are having trouble with your Frigidaire washer giving you an E68 error code. The E68 could be one or both of two possibilities.

First, it could be the heating element. If the heating element goes out, this means that you would be unable to get the water temperatures to hotter temperatures.

Second, it could be something going on with the main control board inside your washer.

With you receiving the E68 error code, I suggest that you give your washer a hard reset, by either unplugging it or shutting the power off at your home's circuit breaker for 2-3 minutes. When you restore the power, if you are still receiving the E68 error code, I suggest contacting your local authorized technician for further assistance. Hope this is helpful.

-Best Regards-
WP

You may have an igniter issue, thermostat, or a gas valve coil issue. Make sure a heat selection is made also.

https://www.repairclinic.com/RepairHelp/Dryer-Repair-Help
This link should help get a proper diagnosis and parts.

I’m happy to assist further over the phone at https://www.6ya.com/expert/david_dc2f9e0a44104720

Please click the link below to see my answer to a similar E68 question on fixya:
https://www.fixya.com/support/t10225683-error_code_e68_frigidaire_affinity

Frigidaire Affinity dryer model AEQ7000ESO error code E68 (stuck button). Sometimes a 'stuck button' code really is a stuck button. I took the circuit board off the front panel.On the back side of the front panel, each button has 3 short plastic posts, 2 on one side and 1 on the other.The center part moves to push a longer piece that contacts the circuit board. When I push the top of a front stadium-shaped button, the center plastic piece moves too far, touches the short post, and sticks (maybe due to age). When I push the bottom of the front button, the plastic piece goes far enough to contact the circuit board and not far enough to touch the short post. To prevent a stuck button, we now press the bottom of the front buttons.So far so good. If it happens again, I plan to shave or file a little bit off the top edge of the post to give it more clearance. 1st photo: pencil points to stuck parts. 2nd photo: unstuck parts, 3rd photo: the front of our dryer.

The error code E68 means a key or button is stuck. Check the buttons by pressing them one at a time to find the stuck one or enter the service diagnostic mode then the key function test. Click on the link below for the detailed instructions.

Troubleshooting Error Code E68 on Frigidaire Affinity and Gallery Dryers