Bosch gas dryer nexxt

Try cleaning out the compartment below the lint filter. There's a sensor in there that is probably buried in lint.

http://www.ebay.com/itm/Bosch-Nexxt-Dryer-Model-WTMC3300US-01-Fan-Blower-Housing-5070000460-/160948680806?pt=LH_DefaultDomain_0&hash=item257949f866

Hello,

This means that the dryer is not able to exhaust correctly. Often times this is caused by kinked or blocked vent behind the dryer. If that looks ok, the vent in the wall may need to be cleaned. In this case or in most a professional dryer vent cleaner would be needed to clean the dryer vent.

One last thing you can check is the lint screen. On Bosch dryers the lint filter will become clogged from the dryer sheets. Remove the lint filter and run water through it. If water runs through, the lint filter is good.

I know this unit well and can assists you with any repair related question you have.

Let me know

This was a previous post, but it may work for you.

A friend of ours has a bosch gas dryer and she had the same problem. She called the Bosch repairman and he sprayed the lint filter with Greased Lightning to clean out the tiny holes in it. He charged $100 and left. He said it would take care of the problem. Has not had any problems since. http://www.greased-lightning.com/ It is worth a try.

Motor won't work
Lint screen hi-limit (thermal cutout) tripped.
Clean lint screen and clean lint and other debris from front shield, then replace hi-limit. Also check exhaust duct length & # of elbows.
Wire harness failed.
Run resistance or continuity checks to track down broken wire or connector. Replace failed wire harness.
Display shows "E:01" during drying.
Lint filter, air duct or air damper is blocked.
Air leaking past felt drum seal.
Air duct is too long, too small or has too many bends. Inadequate ventilation around dryer (i.e. in a closet).
Clean out filter, air duct and air damper.
Replace felt drum seal. If seal doesn't fit snugly onto drum, wet felt and dry it by running a timed dry cycle for 20 minutes (felt will shrink and fit drum snugly).
Shorten, enlarge, reroute and reduce # of bends in air duct. Move dryer to an area

Hi,
This indicates the sensor near the lint filter gets too hot. This is usually caused by bad air flow.Try running the unit without the vent hose attached. If the problem goes away the problem is in the ducting.
You may need to have it cleaned out. May be lint filter is clogged due to the use of dryer sheets or fabric softener. You can try to clean the filter with Windex.
If neither one of this suggestions resolves the issue there may be a problem with the sensor, there may be heat escaping somewhere within the dryer. This is only resolved by technician.


Good Luck and have a nice day.
Rating the solution is highly appreciated.

if you use fabric softener sheet,there is two small metal chrome stip take a wet rag clean them off,they are locate on the in side of dry drum close to dry grill on inside,those sheet can leave a film on those stip are your sensor for the auto cycle on the dryer

If you look on the insideiof the dryer door toward the top . you should see a clamp or something ..if that clamp or screw is broken it will nit operate and giv eyou an error messsage ... what we did was put a little screw back into that hole and made sure it;'s long enough to push in the button at the opening of the dryer .. try that .. if that does not work then you might want to try . to replace the dryer plug ( and or electrical box) if you have a 3 prong outlet and cord then that will give you the error message also , these dryers are picky ...

This is a common complaint with this dryer.The probe generating this problem,is at fault.It likely has a film on it,from the dryer sheets.Remove the lint screen,and wipe down the probe that sticks into the air box.Should fix the problem,if not ,replace the probe.

hi there,

i understand your frustration here.

the E01 code means there is reduced airflow through your dryer and therefore before it overheats and starts a fire, it shuts down.

replacing boards and sensors will not fix this problem as it has nothing to do with the electronics or electrical side.

here is what you can do yourself:

check the venting on the dryer.
the vent hose runs from the back or side to the wall of your house.
it may be clogged or kinked

if everything is fine, i would contact Bosch directly and see if they have a recall or any service reports on this problem and if there are any solutions.

let me know if i can be of more assistance.

thanks.