LeapFrog Leapster Learning Game System - Answered Questions & Fixed issues

maybe damaged pin connectors or corroded loose . almost works but not getting proper feed.

leapster initially worked but now will not work, batteries are fine

This is usually cause by extremly hard impact which can dislodge the contacts between the Screen and its mating contact on the circuit board. This requires opening the device and attaching/repositioning the connector, whilst the divice is open you should place a small amount of hot glue on the outer part of the contact to prevent it moving. DO NOT use solvent based adhesives or super glue as this will severly damage the device. If this does not solve your problem contat me on [email protected] and I will try to assist you further.

Answer
I had the same problem and here is the answer I found at leapfrog.com which fixed my daughter’s disney princess leapster 2’s problem. Good luck!
If your Leapster2 does not respond to the stylus pen, it needs to be calibrated. Calibrating the Leapster2 is easy:
1) Ensure that a cartridge is not inserted
2) Hold down the Hint (?) button while turning the unit on. Continue to hold the Hint button down until the LEAPSTER menu appears.
3) When the LEAPSTER menu screen appears, press the A button
4) Touch each of the crosshairs that appear with the stylus
5) Restart unit

Contact Customer Service they may be able to replace the unit even after warranty 800-701-5327

Contact customer service 800-701-5327 they might be willing to replace the unit. Hope this helps!

Contact Customer Service the might be willing to replace the unit even after the warranty has expired 800-701-5327

Contact Customer Service they might be willing to replace the unit even after warranty has expired 800-701-5327

Contact Customer Service they might be willing to replace the unit even after warranty 800-701-5327

There are a number of possible reasons your toy may have stopped working. Sometimes it helps to clean the battery compartment with a dry cotton swab or cloth. Rub the gold contacts inside the battery compartment to release any dust or film. You can also use an eraser to 'erase' and clean the contacts. Once you have cleaned the contacts, please make sure to install new non-rechargeable batteries before turning your unit on.

If the toy still does not work, it may have been dropped or handled improperly

If your Leapster2 does not respond to the stylus pen, it needs to be calibrated. Calibrating the Leapster2 is easy:
1) Ensure that a cartridge is not inserted 2) Hold down the Hint (?) button while turning the unit on. Continue to hold the Hint button down until the LEAPSTER menu appears. 3) When the LEAPSTER menu screen appears, press the A button 4) Touch each of the crosshairs that appear with the stylus 5) Restart unit

If your Leapster2 does not respond to the stylus pen, it needs to be calibrated. Calibrating the Leapster2 is easy:
1) Ensure that a cartridge is not inserted 2) Hold down the Hint (?) button while turning the unit on. Continue to hold the Hint button down until the LEAPSTER menu appears. 3) When the LEAPSTER menu screen appears, press the A button 4) Touch each of the crosshairs that appear with the stylus 5) Restart unit

Contrast button on bottom that adjusts.

pull straight up after turning power off

Try pressing the on/off button to turn it off. I had a same problem. I depressed the on/off button for ~6 second or so and the device turned off. When I turned on again, the LeapReader no longer had a white light and was recognized by my computer.

Enter 1111 and it will say oops wrong password then enter 419 backspace and get rid of the 9 and then 27 worked like a charm took forever to find one that worked and this one worked for me once in change the 4 digit code to something ez

That's what I've been asking.??

Get a new Leapster

uefwiagyrskef

https://s7.leapfrog.com/is/content/LeapFrog/Site%20English%20Assets/Support/Download/Parents%20Guides/80-602000-LeapPad-Ultimate-Parent-Guide.pdf