NorStar Meridian M7310 Phone - Page 5 - Answered Questions & Fixed issues
Norstar Meridian how to turn on the ringer
From the following web site:http://www.telephonemagic.com/phone-support/norstar-feature-programming-code.htmTo Change the Ring Volume:
1. Press the Feature button, then * 80
2. Press the volume key up or down
3. Press the release key1 to exit and save the volume level
Mute speaker on M7310
I've had Nortel Norstar m7310 phones for years and the entire time that I've them, I've never used the speaker phone. I could hear them, they couldn't hear me. At this site, I figured out how to fix that and now the speaker phone works. It created another problem. For me to use the Called ID, I would have to press the line that was calling and I would see who it was that was calling. Now, when I do that, it immediately picks up the phone versus letting see who is calling. I want to be able to both see who is calling and use the speaker phone. Thanks.Parts For BMW
We have a Nortel Norstar M7310. Approximately ten
my recommendation is to put the same model phone at that station and see if it does the same thing. Its been almost ten years since I installed those systems, but I do remember that you can swap phones and locations as long as the phone model is the same. my guess is that the phone is broken somehow as those symptoms arent really a programming issue. The individual button programming stays with the location and not the phone, therefore you would have the exact same lines and programmed buttons if you could temporarily replace.
hope this helps some
I have a Nortel M8X24-DS
Do you have stand alone phone or is it equipped with a forwarding / data system? I need model of answering system if you have it. Otherwise you should be able to set it up by reviewing owners manual. Is phone hooked up to computer also or just phone line?
FixYa Support
I am new to this
Hi there, in regards to voicemail, many service providers have different ways of setting up voicemail ... most of them have different input types of codes which you can enter with your phone keypads. This will either activate or disactivate the voice mail. The best thing is to ring them up and ask them for this code. I can help you further but then I will need all your details of your phone provider and I think this will be a longer process than calling them. I hope this helps and if you have any questions please do not hesitate to contact me. Good luck with that. Hope this helps.
I have a 7308M that
In an 824 or higher system, you can't program from a 7208. You need a 7310 or 7324 phone. You may also need to program it from extension 21(221).
Carl
How do I activate the
familirize with devices user manual whether has feature functions requested. Second, ascertain that device was least malfunctioning since acquired. normally, familirising with innovative devices makes expertise in functionality.
Trying to change the intercom caller ID onthe
Programming is done on 7310, 7324 and 7316 type sets.
Enter programming by pressing the feature key followed by **266344.When prompted to enter the password enter 266344.
The screen should say TERMINALS&SETS. The 4 top line/feature keys are now used for programming.
At the terminals&sets prompt, press the show key (top right arrow).
The display should now ask for an extension number. Enter extension number you want to change the name on.
Press the show key (top right arrow)
The display should say LINE ACCESS
Press the next key (bottom right arrow) .
The display should say CAPABILITIES.
Press the next key (bottom right arrow) .
The display say Name.
press the Chng soft key.
use the dial pad to enter the name. advance using the arrow soft key to go to the next letter
ex. Bill = 2,2 -> 4,4,4 -> 5,5,5 -> 5,5,5
Press the next key (bottom right arrow) to enter the name.
Press the release key when finished
One of our Meridian Modular
Mostly this happens when the unit has been used by someone else. Most fairly used units or refurbished units encounter this. Mailboxes are meant to be for rivate use therefore when a password is set on it the feature 983 do not work on it because a password has already been set.
Usually what i advice is for you to take it to the dealer and make an official complaint often times they would replace the system processing memory and once this is done although all previous information on the unit will be lost but you wont have the problem of a locked mailbox. Other than this unless you find who put the password and ask them what it is. This problem could also have been caaused by poor programming of the unit initially.
Hope this solution has been helpful?
Thank you for visiting FixYa.
Hello. Can I make the
Of course it's possible, however, you need to turn off Auto Set Relocation. I'm not sure if it's an Administrator or only an Installer function.
There is a trick....and I've never tried it because I HATE ASR, if you unplug the old phone, move it to the original location, and wait at least 5 minutes, then unplug it from the original location and plug in the NEW phone before you plug in the phone you just unplugged, the new phone will become the old extension and your original phone will be unprogrammed. It also says you have to wait at least one minute before you can change the DN of a new phone, but that requires INSTALLER access.
Like I said......
Carl
.
I have a 1987 Meridian
From the idle 7310, press FEAT *2 the button and dial their extension.
If you get a nasty notification, like Denied in Admin, or Set Locked, you'll need the system administrator password and procedure to unlock the phone..
Carl
I just bought a
A defaulted system has 2 lines assigned until you program them. It's programmed from the installation manual of the phone system. There, under Terminals & Sets, you tell the system how many intercom paths, whether it's handsfree, and how many lines are assigned. Once you fill in all the information, you can Copy the set to all the other sets and you're done.
Carl
There is no dial tone
Does it work on handsfree or with the handset ? It should work for one of those. Make sure your handset isn't plugged into the headset port on the bottom of the telephone. If it's still not working, change the handset and curly cord with one from another phone to test if that's the issue. (but then the Handsfree should technically work)
I work at a small
In the mailbox setup, there's a prompt called EXT .. make sure your extension number is there. There's another prompt called MSG WAIT (or something like that) which needs to be set to YES or Y. The person that setup the mailbox should be able to get to these settings.
We have a meridian M7310
First of all, make sure you're plugged into the headset port of the telephone and not the handset port. Pressing the Handsfree button should change from handset to headset. You can't use the speaker phone with the headset plugged in.
Not finding what you are looking for?