20 Most Recent NorStar Meridian M7310 Phone - Page 7 Questions & Answers

From the following web site:http://www.telephonemagic.com/phone-support/norstar-feature-programming-code.htmTo Change the Ring Volume: 1. Press the Feature button, then * 80 2. Press the volume key up or down 3. Press the release key1 to exit and save the volume level

I've had Nortel Norstar m7310 phones for years and the entire time that I've them, I've never used the speaker phone. I could hear them, they couldn't hear me. At this site, I figured out how to fix that and now the speaker phone works. It created another problem. For me to use the Called ID, I would have to press the line that was calling and I would see who it was that was calling. Now, when I do that, it immediately picks up the phone versus letting see who is calling. I want to be able to both see who is calling and use the speaker phone. Thanks.Parts For BMW

Programming is done on 7310, 7324 and 7316 type sets.
Enter programming by pressing the feature key followed by **266344.When prompted to enter the password enter 266344.
The screen should say TERMINALS&SETS. The 4 top line/feature keys are now used for programming.
At the terminals&sets prompt, press the show key (top right arrow).
The display should now ask for an extension number.
Enter extension number you want to change the name on.
Press the show key (top right arrow)
The display should say LINE ACCESS
Press the next key (bottom right arrow) .
The display should say CAPABILITIES.
Press the next key (bottom right arrow) .
The display say Name.
press the Chng soft key.
use the dial pad to enter the name. advance using the arrow soft key to go to the next letter
ex. Bill = 2,2 -> 4,4,4 -> 5,5,5 -> 5,5,5
Press the next key (bottom right arrow) to enter the name.
Press the release key when finished

my recommendation is to put the same model phone at that station and see if it does the same thing. Its been almost ten years since I installed those systems, but I do remember that you can swap phones and locations as long as the phone model is the same. my guess is that the phone is broken somehow as those symptoms arent really a programming issue. The individual button programming stays with the location and not the phone, therefore you would have the exact same lines and programmed buttons if you could temporarily replace. hope this helps some

you can contact the service provider....

you can contact the mobile service provider......

Do you have stand alone phone or is it equipped with a forwarding / data system? I need model of answering system if you have it. Otherwise you should be able to set it up by reviewing owners manual. Is phone hooked up to computer also or just phone line?

FixYa Support

Hi there, in regards to voicemail, many service providers have different ways of setting up voicemail ... most of them have different input types of codes which you can enter with your phone keypads. This will either activate or disactivate the voice mail. The best thing is to ring them up and ask them for this code. I can help you further but then I will need all your details of your phone provider and I think this will be a longer process than calling them. I hope this helps and if you have any questions please do not hesitate to contact me. Good luck with that. Hope this helps.

In an 824 or higher system, you can't program from a 7208. You need a 7310 or 7324 phone. You may also need to program it from extension 21(221).

Carl

it depends on which phone you have sometimes a phone may not have one.

To do this you must use the manual and setup the "Night Switching" extension setup.
Please find below the link to the programming guide. This link below show how to setup the "Night Service".
http://www.phonserv.com/meridian_norstar_programming.htm


http://www.telephonemagic.com/phone-support/norstar-feature-programming-code.htm

I found a PDF file that may help you to configure the settings on your phone:
http://subzerovision.net/manuals/nortel2.pdf
Please let me know if this work or not so that if this will not work for you we will proceed to the other option.