20 Most Recent NorStar Meridian M7310 Phone - Page 5 Questions & Answers

Programming is done on 7310, 7324 and 7316 type sets.
Enter programming by pressing the feature key followed by **266344.When prompted to enter the password enter 266344.
The screen should say TERMINALS&SETS. The 4 top line/feature keys are now used for programming.
At the terminals&sets prompt, press the show key (top right arrow).
The display should now ask for an extension number. Enter extension number you want to change the name on.
Press the show key (top right arrow)
The display should say LINE ACCESS
Press the next key (bottom right arrow) .
The display should say CAPABILITIES.
Press the next key (bottom right arrow) .
The display say Name.
press the Chng soft key. (or the clear key to erase)
use the dial pad to enter the name. advance using the arrow soft key to go to the next letter
ex. Bill = 2,2 -> 4,4,4 -> 5,5,5 -> 5,5,5
Press the next key (bottom right arrow) to enter the name.
Press the release key when finished

Conference [Feature] [3]

• Establish a conference call between yourself and two other parties.

1. Make or answer the first call.
2. Put the first call on hold.
3. Make or answer the second call.
4. After the second call is connected, press [Feature] [3].
5. Press the line or intercom button of the first held call.
6. Press [Rls] to end the conference call

• To remove yourself from a conference permanently (unsupervised conference):

• Press [Feature] [7] [0]. The other two callers remain connected. (Some external lines may not support this feature.)

Programming is done on 7310, 7324 and 7316 type sets.
Enter programming by pressing the feature key followed by **266344.When prompted to enter the password enter 266344.
The screen should say TERMINALS&SETS. The 4 top line/feature keys are now used for programming.
At the terminals&sets prompt, press the next key 7 times(bottom right arrow).
The display should say system programming.
Press the show key (top right arrow)
*On newer versions, The display should say hunt groups
Press the next key (bottom right arrow) .
The display should say Change DNs
*On older versions, the display should say Change DNs
Press the show key (top right arrow).
Enter in the old dn number i.e.229.
Press the show key(top right arrow)
enter the new dn number i.e. 225
Press the show key (top right arrow)
Press the Rls key.

To Log Into System Programming:
Press FEATURE * * 2 6 6 3 4 4
Enter Password: 2 6 6 3 4 4 Display will read: " A. Configuration"
Using the navigation keys, as displayed below, follow the next simple steps:
Press: NEXT Display will read: "B. General Admin"
Press: SHOW Display will read: "1. Sys speed dial"
Press: NEXT Display will read: "2. Names"
Press: SHOW Display will read: "1. Sys speed dial"
Press: NEXT Display will read: "2. Names"
Press the SHOW Display will read: "Set names"
Press: SHOW Display will read: "Show set:__"
Enter the extension number of which you wish to change the name Display will read: "<##:name>"
Press the CHANGE softkey
Using the dial pad spell out the name Ex: If you need the letter K press the 5 key twice and then press # to confirm the letter. Continue until the entire first name is spelled. (note: you are limited to 7 characters)
Press: NEXT (if you fail to do this step, the name will not be saved!!!)
Press the RLS key

Hope this helps!

Try these sites:http://www.telephonemagic.com/phone-support/norstar-feature-programming-code.htmhttp://www.ask.com/faqcentral/NORSTAR.htmlhttp://www.gfaelectronics.com/programnorstar.htm

Can you re-phrase....did not understand what you are trying to do.

Intercom button/s provide dial tone when they are pressed. They are required to call other phones on your system.Sounds like your button is stuck or issue with the motherboard.

F983 then enter the ext # manually (not a speed dial/button), you must have 2 Intercom keys programmed on your phone.

You need to access Admin programming in the phone system and navigate to Capabilities and change the Forward No Answer to the DN of the voicemail....if unsure of any of this you need to be calling your vendor that handles the system for all issues or questions.

A Nortel Key Service Unit, an ICS (MICS,CICS), BCM (50,100 etc), Norstar (308,616,824), an Avaya IP Office running Nortel cards, or there is another company that makes a Nortel emulation key system but I can't recall what it is right now.Carl

Mod cord, cable, jack or system port issue, call in your local tech/vendor to repair it.

You must do it from the control set only, usually reception set.Feature 871 and choose the mode you want such as Normal.

If you only have one line,why not just lose the Nortel system? You can reuse the wiring from the phone sets to the contoller as regular inside wire,and just plug in regular phones(and maybe put the Nortel phones and controller on EBay and make a few bucks off it!)