20 Most Recent NorStar BCM-T7208 Corded Phone - Page 4 Questions & Answers

the buttons are not programmed properly. Use 'feature * 0' to see what is on the buttons. press feature * 2, press the key, then dial the extension #. this will program the key with the proper extn #

NorStar Lands... | Answered on Feb 11, 2015

"Q: My Norstar Startalk, Flashtalk, or voice mail says my mailbox is not accepting any more messages. I deleted all my messages, but callers still cannot leave a message. Why?
A: Check with your voice mail administrator. Chances are another Mailbox on the system used up all the message storage space. Usually it's the general delivery mailbox that hasn't been checked for messages on a regular basis."
Frequently Asked Questions

The following discussion suggests that voicemail can be inactivated, and cab be re-activated by logging in and pressing '4'
Startalk Flash Won answer Nortel Phone System Tech Support

This says that the mailbox must be initialized.

NorStar Lands... | Answered on Oct 06, 2014

I would just COPY the settings from another extension that is the closest or same as what you want...

F**CONFIG ... Terminals&Sets ... (enter "good" extension #) ... COPY softkey ... (destination extension) ... System&User ... and you're done.

NorStar Lands... | Answered on Oct 06, 2014

Feature 3 or Transfer if you have a hard or softkey

NorStar Lands... | Answered on Oct 06, 2014

F**TIME F**8463

NorStar Lands... | Answered on Oct 06, 2014

A model number would help. What # phone, what # expansion box"?

NorStar Lands... | Answered on Oct 06, 2014

First you have to check your service provider if you have activated this service because here in South Africa it cost a nominal fee for caller ID

NorStar Lands... | Answered on Jul 16, 2014

should you dial 9 or another access code for outside calls?

If if you dial an "outside" number on an intercom line it will look at the first 2-3 digits as another extension. You need to dial the Central Office access code, or use a line key assigned to an outside line.

NorStar Lands... | Answered on Jun 24, 2014

Feature * 0 then press an intercom key.

NorStar Lands... | Answered on Jun 24, 2014

Do you have a dial tone?? Try dialing 9 then number..

NorStar Lands... | Answered on May 13, 2014

It is probably made that way, but if it wasn't like that out of the box first plugged in, than there should be a button to make it brighter. (or it might just be you...)

NorStar Lands... | Answered on Apr 08, 2014

This would depend on if the line is a stand alone line only being assigned to one extension or on a PRI having DID service. Do a Feature *0 and check the line buttons. It will show the line number or target line number. With this information you can check it in one of two ways. If it is a stand alone line and provided a line number, access the line by pressing the line and dialing your cell phone to get the Caller ID information. If it associated with a PRI having DID service, you will have to check the target line information in programming. A system administrator or vendor needs to do this.

NorStar Lands... | Answered on Feb 09, 2014

The lines have been restricted in the phone system for some reason that might not be needed anymore. Check with your Phone System Administrator. A system vendor can make these changes or an administrator with programming knowledge.

NorStar Lands... | Answered on Feb 09, 2014

Not finding what you are looking for?
NorStar BCM-T7208 Corded Phone Logo

32 questions posted

Ask a Question

Usually answered in minutes!

Top NorStar Lands Phones Experts


Level 3 Expert

84625 Answers

Thomas F. Schneider

Level 3 Expert

2715 Answers

Cindy Wells

Level 3 Expert

5869 Answers

Are you a NorStar Lands Phone Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

NorStar Lands Phones

  • NorStar Lands Phones

Most Popular Question

cancel not disturb option

  • Lands Phones