20 Most Recent
Lutron Claro Screwless 2 Gang Wall Plate for Dimmers - Page 5 Questions & Answers
I have a onan 4000 LP generator when I try to start it it starts and then goes dead?
Here are some common troubleshooting steps to help you identify and potentially resolve the problem:
- Fuel Supply:
- Check the LP (propane) fuel supply. Ensure that there is enough propane in the tank.
- Check for any obstructions or kinks in the fuel line.
- Air Intake and Exhaust:
- Make sure the air intake and exhaust are not blocked. Lack of proper ventilation can cause the generator to shut down.
- Choke Position:
- Check the position of the choke. If it's set to "Choke" for starting, make sure to gradually move it to the "Run" position once the generator has started.
- Fault Codes or Indicator Lights:
- Look for any fault codes or indicator lights on the generator control panel. These can provide clues about specific issues.
- Oil Level:
- Check the oil level in the generator. Some generators have a safety feature that shuts them down if the oil level is too low.
- Spark Plug:
- Inspect the spark plug for fouling or damage. If needed, clean or replace the spark plug.
- Fuel System Issues:
- Inspect the fuel system for any leaks or issues. LP generators may have a fuel filter that needs to be checked and, if necessary, replaced.
- Carburetor:
- The carburetor may need cleaning or adjustment. If it's clogged, it can lead to stalling issues.
- Battery Voltage:
- Ensure that the generator's battery has sufficient voltage. A weak or dead battery can affect the starting process.
- Generator Load:
- If the generator is under a heavy load, it may shut down. Try starting it without any load and then gradually add loads.
How can I clear this because I can't recharge my prepaid meter.
rF Con means there is no RF connection.
Try this;
* Press the Back arrow on the keypad - this step is to refresh the UIU ( the device)
* Type # 75 # - this is to check the signal strength
If it does not go back to the normal display
*Type # 80 # - this is to refresh the meter
Then lastly you can repair the meter and the UIU by # 36 #
The above steps will work better if you are outside the house because the meters uses the radio frequency connection
The above error will occur in instances of bad weather conditions or if there is load shedding or power failure
If the problem persists after trying the above you may contact the municipality or the service provider."
What could cause all electrical outlets and lights on the same circuit to go out without tripping the breaker?
GFCI and overcurrent protection (breaker) work in different ways. Suffice to say the GFCI is ~2000x more sensitive and trips long before the typical household breaker. So it's normal for a GFCI trip and the panel breaker to remain closed.The electrician is correct regarding GFCI devices. One GFCI device can protect multiple downstream outlets but some homeowners want a separate reset per floor or each bathroom to have its own reset, etc.As for the hair dryer... you're trying to eliminate trip sources so just leave it unplugged between uses and you'll get your answer.Typical trip sources are the GFCI itself (defect/damage/age) or an appliance of sorts. Then there's rodent or water infiltration issues. Anything you plug into the GFCI circuit is a potential trip source even something seemingly innocuous as a nightlight or air freshener, USB charger, anything that fits into the plug.
How to open the Hubbell YQ230 in order to test line voltage.
Turn off the power source to the device you want to test.
Unplug the adapter from the power source.
Locate the two screws on the adapter's faceplate.
Use a screwdriver to remove the screws.
Gently pull apart the two halves of the adapter.
Once you have opened the adapter, you can use a voltage indicator to test the line voltage . If you don't have one, you can purchase it from Hubbell's website or any other electrical equipment supplier. The MarineEngine.com website states that the Hubbell YQ230 adapter has a UV-resistant housing and two screws on its faceplate. You can use a screwdriver to remove these screws and open the adapter.
Not finding what you are looking for?