Top 20 Samsung RB2155SH Bottom Freezer Refrigerator - Page 5 Questions & Answers

If your Samsung RF220NCTAWW freezer is too cold, there are a few possible causes and solutions:

1. Check the temperature setting: Make sure the temperature setting is set to the recommended level, which is typically between 0 to -5 degrees Fahrenheit. If it is set lower than recommended, adjust the setting to the recommended level.
2. Check the door seal: A damaged or poorly fitting door seal can cause the freezer to be too cold. Check the seal and make sure it is clean and undamaged. If it is damaged, replace the seal.
3. Check the thermostat: A faulty thermostat can cause the freezer to be too cold. Test the thermostat using a multimeter to determine if it is functioning properly. If it is not functioning properly, replace the thermostat.
4. Check the defrost system: If the defrost system is not working properly, it can cause the freezer to be too cold. Check the defrost heater and thermostat to make sure they are functioning properly. If they are not functioning properly, replace them.

If none of these solutions work, you may need to contact a professional appliance repair service to diagnose and repair the issue.

If the metal strip on your Samsung Cool Select Drawer slider has come out, you may be able to fix it yourself with the following steps:

1. Remove the Cool Select Drawer from the fridge.
2. Locate the metal strip and examine it to determine how it came out. If it's bent or damaged, you may need to replace it.
3. Reattach the metal strip to the slider by sliding it back into the groove in the slider. If it's loose, you can use a pair of pliers to carefully bend it back into place.
4. Once the metal strip is back in place, slide the Cool Select Drawer back into the fridge and test it to make sure it's sliding smoothly.

If you're unable to fix the problem yourself or the metal strip is damaged beyond repair, you may need to contact Samsung customer support or a professional repair service for assistance.

To remove the back panel inside an American Samsung fridge, you will need to follow these steps:

1. Unplug the fridge: For safety reasons, make sure to unplug the fridge before you begin.
2. Remove food items: Take out all the food items from the fridge and place them on a table or counter.
3. Locate the screws: Look for screws on the inside walls of the fridge that hold the panel in place. They are usually located on the sides of the panel near the top and bottom.
4. Remove the screws: Use a screwdriver to remove the screws and keep them in a safe place so they do not get lost.
5. Release the clips: There may be plastic clips holding the panel in place. If so, gently push the clips in with a flathead screwdriver and pull the panel away from the wall.
6. Access the back of the fridge: With the panel removed, you should now have access to the back of the fridge where you can place the steamer to melt the ice.
7. Reassemble: Once the ice has melted, reattach the panel by securing the screws and clips, plug the fridge back in, and return the food items to the fridge.

Note: Make sure to follow all safety precautions and wear gloves if necessary to avoid any potential hazards, and if in doubt, it may be best to consult a professional for assistance.

There could be a few reasons why the control panel buttons on your Samsung refrigerator are not working. Here are a few things you can try to fix the issue:

1. Make sure the fridge is plugged in and the outlet is functioning properly.
2. Check if the fridge is in Demo Mode. This is a feature that disables the control panel buttons when the fridge is in a store or showroom. To exit Demo Mode, press and hold the "Power Cool" and "Power Freeze" buttons for 8-10 seconds.
3. Check if the control panel lock feature is activated. This feature prevents the buttons from being pressed accidentally. To deactivate the lock feature, press and hold the "Lighting" and "Fridge" buttons for 8-10 seconds.
4. If none of these solutions work, there could be an issue with the control panel itself. In this case, it is recommended to contact Samsung customer support or a qualified appliance repair technician for further assistance.

This could mean that your refrigerator is not defrosting correctly, which can cause too much ice to build up in the vents. To fix this, you'll need to check the evaporator and defrost heater to ensure they are working correctly. Additionally, you may need to replace the defrost timer or defrost thermostat. If the issue persists, you may need to contact a professional for further assistance.

The SRL709EVSS is a Samsung refrigerator model, but unfortunately, since it's an older model, some parts may have been discontinued by the manufacturer. To get the correct part numbers for the heater, sensor, and frost kit element for your specific model, I recommend contacting Samsung customer support or an authorized Samsung service center. They should be able to provide you with the necessary part numbers and potentially offer alternative solutions if the original parts are not available. Additionally, it's worth noting that the frost kit element and heater are not the same thing. The frost kit is typically a component that is used to prevent frost buildup in the freezer compartment, while the heater is responsible for defrosting the evaporator coils.

The 'd' error code on your Samsung refrigerator indicates a problem with the refrigerator's defrost system. This could be caused by a number of issues, such as a faulty defrost heater, a faulty defrost sensor, or a problem with the control board. To troubleshoot the problem, you can try resetting the refrigerator by unplugging it from the wall outlet for at least 5 minutes, then plugging it back in. This will reset the control board and may fix the issue. If the problem persists, you may need to check the defrost heater and sensor to see if they are functioning properly. If they are not, they may need to be replaced.

It sounds like there may be multiple issues with your Samsung refrigerator. Here are a few steps you can try to troubleshoot the problem:

1. Check the water valve: Make sure that the water valve is open and functioning properly.
2. Check the water line: Make sure that the water line is not kinked or damaged.
3. Check the water filter: Make sure that the water filter is properly installed and not clogged. If you are having trouble with the filter not screwing in properly, you may want to try a different brand of filter.
4. Check the defrost drain: Make sure that the defrost drain is not clogged or blocked, and that the drain tube is not obstructed by rust.
5. Check the water tank: Make sure that the water tank is not damaged and that it is properly sealed.
6. Check the grommet: Make sure that the grommet is not cracked or damaged.
7. Consult the manual: Consult the manual for specific troubleshoot and service information for your Samsung RF26VABPN refrigerator model.

It's important to note that these steps are general guidance and the specific steps may vary depending on the model of your Samsung refrigerator. Make sure to consult the manual for the specific steps and precautions before performing any maintenance or repairs on your refrigerator. If the problem persists, it is best to contact Samsung customer service or a professional for further assistance and repair options.

It won't make ice instantaneously you have to have your water supply turned on to the ice maker in order for it to make ice it takes a while before ice cubes can be made it's not an instant thing

Hi, if 2 lines appeared just after you changed the tv's position, then I'm thinking that the pressure from the floor is the cause of the issue. Are you using the type of tv stand advised by Samsung or just placing the base of the tv (almost) directly on the floor ? If you don't have a stand, you might need to get one in order to overcome your issue. If I'm correct, hanging your tv again should help temporarily overcome the issue. Thank you.

https://www.google.com/search?q=Samsung+RF28HMEDBSR%2FAA+beeping+and+energy+saver+light+on

Samsung Refrigerator Randomly Beeping - What Causes ...

https://removeandreplace.com > ... > Refrigerator Repair Jun 9, 2018 - My refrigerator keeps beeping/alarming all day long. The Energy Saver icon comes on and off all day long - and the beeping is driving us crazy. ..

A Service Manual is shown, but the site sends you rounds in circles. There is a tantalizing picture of it and your model is listed. https://www.google.com/search?q=Samsung+SR511ENW+%27%22service+manual%22 The reason for your issue of the fridge freezing food is that the fridge is set too cold, also check the circulation fan inside the fridge whilst you are there. The problem with the freezer is likely a failed circulation fan, a failed defrost timer, or a failed defrost element. The evaporator coils will be a solid lump of ice which is preventing the flow of chilled air. My GE Fridge is 20 years old and has had one defrost timer fitted in all that time!

Call for service. Either it needs a refrigerant gas top up, the thermistor has failed or the evaporator fan has failed. It should be 35' - 36'F and should recover in 5 minutes.

light button on right middle and lock at same time with control pad to unlock

The flickering display on your Samsung fridge model RL43WCIH indicates a possible issue with the control board or the temperature sensor. The fact that the on and off button is not working may indicate a power supply problem. Here are a few steps you can try to troubleshoot the issue:

1. Check the power supply: Make sure that the fridge is plugged in and the power outlet is functioning properly. Try unplugging the fridge for a few minutes and then plugging it back in to see if that resets the control board.
2. Check the temperature sensor: If the temperature sensor is faulty, it can cause the display to flicker. You may need to replace the temperature sensor if it is damaged or not functioning properly.
3. Check the control board: A faulty control board can cause a variety of issues, including a flickering display and unresponsive buttons. If the control board is the problem, you may need to replace it.

If these steps do not resolve the issue, it may be best to contact a professional technician to diagnose and fix the problem.

Call the engineer back under warranty on the work he did. Warranty is normally 6 months on parts exchanges.

possible dirty or bad level sensor

The lever and also the switch is jammed in your fridge and fridge water inlet valve is broken.If the water is dripping slowly then there is air is stuck in the water line or ice has built up in the chute.

If the ice maker on your Samsung RF18HFENBWW refrigerator continues to turn on and off despite not being hooked up, it's possible that the switch or sensor controlling the ice maker is malfunctioning. You may need to replace the ice maker assembly or have a technician look at it. In the meantime, you can try turning off the ice maker manually by following these steps:

1. Open the refrigerator door and locate the on/off switch for the ice maker. It should be located on the control panel inside the fridge.
2. Switch the ice maker to the "Off" position.
3. Unplug the refrigerator from the electrical outlet for 30 seconds and then plug it back in. This will reset the control panel and may help stop the ice maker from turning on and off.

If these steps do not work, it's best to contact Samsung customer support or a qualified technician to diagnose and fix the issue.