Siemens Gigaset 4215 Cordless Phone - Answered Questions & Fixed issues

I don't have this model but I have had two Siemens phone systems. Typically, when the handset says "Searching" it is trying to connect to the base station (the part actually connected to the phone line). This can happen if the handset is too far from the base station to connect to it wirelessly. It can also happen if the handset has become unregistered from the base station (or was never registered to begin with). If the distance issue is not the problem, look in your documentation for how to register the handset and give that a try.

Go to page 7 of the following manual and you will find your procedure:

http://gigaset.com/medias/sys_master/A31008-M1644-R101-2-7619_ba_NET.pdf

You control the answering machine from the handset. First turn on the answering machine. Press Menu then use the up/down arrows keys to navigate to Ans Machine. Press OK then navigate to Answering M. Look for a check next to this to indicate it is on. Press OK to toggle the answering system on or off. Then press End or left arrow to return to the previous menu. If the machine's memory is full, it will switch off. Delete messages so that the unit will keep the answering machine feature on.

Next to record a new message follow the above steps to reach the Ans Machine menu and press OK. Scroll to Announcements and press OK. Scroll to Record Annc or Rec Annc Only (if no messages will be recorded). Press OK then bring the handset to your ear and listen for the notification of recording and then the tone. State your message clearly into the microphone of the handset. Press End to stop recording and listen to the unit play back your announcement. (It will stop automatically after 170 seconds or a 2 second pause in your speaking.) If an Annc Only message is available, the machine will play it when the memory is full. Otherwise, it will turn off.

To select your announcement (and recording type) follow the above steps to Announcements and press OK. Then scroll to Mode and press OK. Scroll to Annc or Annc Only (available if the Announcement only recording has been made) then press OK. Again OK toggles the announcement on or off; look for a check mark to indicate the announcement will be played. Press End to exit the menu.

Retrevo has the manual for the Gigaset 4215 here: http://www.retrevo.com/support/Siemens-4215-Telephones-manual/id/23319bh144/t/2/ . You will need to enter a code to download the file.

I hope this helps.

Cindy Wells

Read the manual, page 2.

My Siemens Gigaset AS15 Cordless Phone is constantly calling the same number, no matter which number I dial! What shuld I do?
Thank you.

Hi,

If your handset displays Searching or Out of Range and cannot link up with the base when the Talk button is pressed, check the following: 1. Handset may be out of range of the base. Move closer to the base.
2. Make sure the base power adaptor is properly installed and connected to a working electrical outlet.
3. Disconnect the handset battery and plug it in again. Place the handset on the cradle for at least 2 to 3 minutes.
4. Disconnect the power adaptor and remove any back up batteries from the base. Wait for 3 seconds and insert the backup batteries into the base, then plug the power adaptor back into the base. Replace the handset on the cradle for at least 2 to 3 minutes.


Carry out a reset procedure on both the handset and the base to return the settings back to the factory default. Your user guide will guide you through the correct procedure.

post a comment for further assistance.
Thank you for using fixya have a nice day:-)

Hi,
Try with another phone.If the phone line is ok then the fault is with the power supply of the base station.When the power supply is defective this type noises occur and phone dies due to power failure.This could be due to fault in voltage regulator,capacitors.

Some times jack of the headphone could be a problem.open up the phone and get inside the jack area and tweek (bend) the contacts

If your phone uses battery then it is stone dead.Because of this it is not able to produces the signal.When there is no enough voltage it will make distortion and noises and dies.

post a comment for further assistance.
Thank you for using fixya have a nice day:-)

Hii can't get my Siemens A160 to work..the word base keeps flashing on the screen..can you help me with this problem please.

You should contact your service provider and have them reset your phone line connection. They should be able to do it remotely.

i couldnt find a link to your owners manual, but, if you go into the menu in your phone and scroll down to "register handset" that should work

Caller ID in the USA uses the FSK standard. For the most part, caller ID in India uses DTMF (although I have heard of some FSK usage).

I am currently living in New Delhi and have an Airtel home phone line. My switch uses DTMF. I went to the Palika electronics bazaar (I aways use shop number 266 near gate 5, they seem to be a little kinder to foreigners as far as the "final price") and purchased an DTMF to FSK convertor. My US phones now show caller ID information, although using US number seperations ### - ### - ####. I paid R500 but you could probably get it for around R400 if you are willing to put in the time bargaining. It looks like they are also available on Indian Ebay.

Mine says UST001B. It looks like these are low volume items because they stuck the components into a box marked "DSL Splitter" It works to convert the caller ID as advertised.

Did you check to see if the battery leaked? I had a similar experience and it was because one of the batteries had leaked. This might also explain why the keys are stuck.

If you're trying to get 5 handsets to work with one base, it won't work. The 4215 can only handle 4 handsets, the base handset plus 3.

When I had to replace the base of my 4 handset system, the base handset still worked. Therefore I had an extra handset which couldn't be used. So I decided to buy another base. Now I have 6 handsets which can be grouped 4,2 or 3,3.

Then the base is bad. I have 1 base like that also... nothing can be done other than send it out to be rebuilt.

Sorry,

Geno

Try this:
Pick a handheld, press Menu - H/set settings - Reg Handset - Select Base 1, enter 0000 as password. Now on the bottom of the base station press and hold the Register button in for about 10 seconds or until the h/set beeps.

Geno

User manual Siemens Euroset 805 (English - 10 pages)

Manua.ls https://www.manua.ls > phones > Siemens Manual. View the manual for the Siemens Euroset 805 here, for free. This manual comes under the category phones and has been rated by 8 people with an ...

Siemens euroset User Manual

ManualsLib https://www.manualslib.com > ... > Telephone > euroset View and Download Siemens Euroset user manual online. euroset telephone pdf manual download. Also for: Euroset 2015. ..

The same as the one that came out :>) https://www.google.com/search?q=siemens+gigaset+552a+handset+battery+replacement

You can try cleaning under the keys with electrical switch cleaner. However, for the display, you can only check the connections to it. Purchasing a defective specialist phone like this is not a good idea as the only people that can provide spares is the maker. You could ask if they would repair it. https://www.google.com/search?q=Siemens+Profiset+3030 Service manual. Apparently this is the same phone https://xn--mxaakbhnhbevf2c2akw2c.gr/wp-content/uploads/2013/10/ServiceManual_S100en.pdf ....

In the UK we have to ask the provider to display it on the screen of our phones.

Known issue, old phone, time for a new one https://www.electronicspoint.com/forums/threads/siemens-gigaset-8825-parts-info-needed.45694/ Or 50 bucks, ouch https://www.ebayshopkorea.com/main/view?itemID=361379602969 ..