20 Most Recent
Weiser Lock Powerbolt 1000 Lock - Page 3 Questions & Answers
When entering code lock beeps
Here is a link to the Frequently Asked Questions page, which addresses the beeping:
http://www.weiserlock.com/Support/Faq/50160000000HhhZAAS.aspx
Good luck!
Does the green light flash all the time on my
Powerbolt is Beeping?
This is the relevant excerpt from the Powerbolt programming and troubleshooting instructions:
Why is my Powerbolt 1000 unit beeping?
To determine why your lock is beeping abnormally, please follow these steps:
Take out batteries and unplug powerstrip.
Let it sit for 1 minute, then put the batteries back in and wait another minute.
If it does not beep, the keypad needs to be replaced (17733-1).
If the unit continues to beep, the powerboard needs to be replaced (A17734-3,3 Powerboard 1470 brass finish; A17734-3,26D Powerboard 1470 satin chrome finish; A17734-3,5 Powerboard 1470 antique brass finish).
The complete page that I cut this from can be found by cutting and pasting this link into your browser search bar:
http://www.weiserlock.com/Support/Faq/50160000000HhhZAAS.aspx
Since you've already gone through the battery change, this suggests that you need to replace the appropriate Powerboard for your lock.
So this is the link to Weiser Customer Support Page:
http://www.weiserlock.com/en/CustomerService/ProductSupport/SupportContact.aspx
I suggest calling the appropriate toll-free number and having a conversation with a representative about this problem, first of all to confirm that you need the part before you go through the expense. Secondly, they will be able to get the correct part on order for you.
Good luck!
I installed my powerbolt today and it works but
Hello Lil Babe,
The lock is working just as it is supposed to. The beeping after it retracts is an audible signal to let you know that the lock has opened or closed.
The flashing green light is a visual signal to let you know that the lock is "open" and you are able to open the door. When the lock is "locked" the light will flash red momentarilly and then should stay solid red for a brief time.
Everything is working just fine, so congratulations on doing a successful installation of your new electronic lock!
I hope you find this Very Helpful and best regards!
Lock botton unlocks the door and unlock botton
I have installed your Powerbolt, but when I push the Lock Button, it unlocks? What should I do?
First remove the cover on the inside of the Powerbolt unit. On the right hand side under the batteries, you will notice that is says "Door Direction Jumper". If the cap is mounted on Prongs 1 & 2, carefully remove it and move it over so that it mounts Prongs 2 & 3. A is right handed, B is left handed.
Good luck--and please provide feedback if this helps!
We bought a house with this lock and don't
To change your code:
1. Remove the inner cover plate from the lock.
2. Locate the small round reset button near the left side of the circuit board (Red or Black).
3. To program, press the reset button once, then enter your 4-8 digit code on the exterior keypad, then immediately press the middle lock button on the exterior keypad. You will hear a beep. This signals that your code has been accepted.
4. To enter a second code, follow the same procedures as in step 3, but this time press the reset button twice then enter your code.
hope this helps
John
Lost combination
The Weiser brand and Kwikset brand Powerbolt are identical, so these instructions will work just fine for you:http://www.kwikset.com/Customer-Support/Product-FAQs/Faq/50160000000HhhEAAS.aspxChange the batteries with fresh brand-name batteries before you reprogram!
Powerbolt keeps beeping
To determine why your lock is beeping abnormally, please follow these steps: Take out batteries and unplug powerstrip. Let it sit for 1 minute, then put the batteries back in and wait another minute. If it does not beep, the keypad needs to be replaced (17733-1). If the unit continues to beep, the powerboard needs to be replaced (A17734-3,3 Powerboard 1470 brass finish; A17734-3,26D Powerboard 1470 satin chrome finish; A17734-3,5 Powerboard 1470 antique brass finish).Navigate to the complete page that I cut this from by cutting and pasting this link into your browser search bar:http://www.weiserlock.com/Support/Faq/50160000000HhhZAAS.aspxThen go to: US & International/FAQ Categories/Keyless Entry/Powerbolt 1000/Search Results/ How do I troubleshoot my Powerbolt 1000?I suggest calling the appropriate toll-free number and having a conversation with a representative about this problem, first of all to confirm that you need the part before you go through the expense. Secondly, your lock may be new enough for you to talk them into warrantying it, and thirdly, they will be able to get the correct part on order for you.Be prepared to find the replacement costs to be expensive enough to warrant considering a new lock altogether. Personally, I've seen enough problems with the Powerbolt on this website to make me consider buying almost anything but! I think that Schlage makes a pretty good product.
Not finding what you are looking for?