Coleman 10' X 10' Sundome Tent 9160K101 - Page 4 - Answered Questions & Fixed issues
How to light coleman lantern
Kerosene lanterns require a little more than just lighting the mantles. Go to Coleman's website and find the directions (for free) for KEROSENE lanterns. The generator on the lantern needs to be preheated with alcohol before it will actually light. Make sure lantern is a Kerosene lantern and not a white gas (Coleman fuel) type, there is a difference even though they look similar.
12/1/2016 3:27:56 AM •
Coleman 10' X...
•
Answered
on Dec 01, 2016
•
1,142 views
My old Coleman lantern pump failed. How to replace?
Pull the ends of the retainer clip (handle looking thing on the metal pump cover) out of the holes. The pump can be pulled out at that time. I just replaced a pump, and walmart sells replacement pumps. It was very easy.
THE FURANCE IS ABOUT 20 YEARS OLD I HAVE NEVER HAD
Replace the thermocouple. It is the brass or copper tube that goes into the pilot light to detect the heat from the flame. If it is burned out, the gas valve will not open and the pilot will not light. They are universal and cost less than $10.
We need help with setting up coleman 13x9
General tent setup instructions:
thread assembled poles through sleeves
connect one end of poles into tent corners
1 by 1 connect the other end of the pole, work front to back and the tent should assemble quite easy.
How do you put a coleman pellet rifle back
Which model do you have? And how far into the tear-down did you go? Photos, or at least details, will probably get you the answers you require. I'll do what I can to help.
How to stabalize four tent poles in an open area.
if you get four sturdy poles (not normal tent poles) then the best thing to do is to stake the four poles into the ground at a 60 degree angle with the top away from the tent and then use the tension created by the angle to support the tarp.
What are the two pins attached to the eye hole,
Are the are pins attached to the pole attachments tabs at the corners along the bottom or farther up the sides at the corners? If they are at the corners a few feet off the ground, they are probably for the rain fly. If they are ground level they could be for an attachment that may not come with your tent like a vestibule. They could also be used for securing the tent after it has been rolled up. In either case here is a link to your tent that might be helpful. Just scroll down and click on the product manual link.
http://www.coleman.com/coleman/ColemanCom/detail.asp?CategoryID=11020&product_id=2000001976
Regulator on stove is clogged, how do i clean?
IF THIS IS A WHITE GAS STOVE/LANTERN, COLMAN FUEL OR GASOLINE, open drain tank,than unlscrew nut closest to the tank, turn cleaning rod into up possition or turn up fuel knob,unhook cleabing rod,leave in gen, if wont come out do not force, than remove tip on other end,if tip is not steel it will melt, heat gen,and rod till red hot leave on heat till carbon is turned to ash, on fire "camp" 30min. or longer should do the trick, torch will work to. gently up and down if rod does not slide rite out,mite have to repeate heating prosess, blow out ash after cold and rod slides freely. than reassemble, being carefull not to bend cleaning rod tip "inner rod" on lanterns do not over tight soft tip, when lighting after cleaning, some times hard to light until ash is worked out of rod and gen. works great! if to dirty replace.
How to put up a coleman tucana tent
Wow. They put more and more stuff on tents. I'll give it a try based on a photo I found.
First, peg the four corners down. This will help it from moving around.
Find the two longest poles. These are your main supports and once you get them in, you can use the tent without the fancy rain cover (if you want to). They should run diagonally from the corner's you pegged. Start at one corner and slide the poles through the sleeves in the top of the tent towards the opposite corner.
The next two longest go from back to front. They do not cross diagonally. Slide these into their sleeves.
Now the hardest part. Slide a pole into a peg hole or a pin (if your poles have holes in the bottom), then bend the pole and attach it to it's corresponding corner. Just let the bent poles lay on the ground. Do the same with the others. It shouldn't matter which poles go up first, but I would do the diagonals myself, then the side supports. Once these 4 poles are up, you're in business.
To attach the monster rain cover flip the whole thing over the top and figure out which side goes to the door. It looks like the lantern is on the right front.
It looks like you should have two poles left. One may be the same size as the side support poles, or very close to it. This is the front door pole. The smallest pole is the side roof support.
Slide the front door sleeve through it's sleeve, then attach it to the pins or holes where the diagonally support poles are. They should have two pins in this spot, one for ea pole. Next, slide the side support pole side to side under the roof, but over the tent. It should have little pockets to put the pole into. Last, you'll have to bungie the hooks to the little rings at each corner of the rain cover. Forget all the strings, unless you want to stake them out to stretch your tent a little. Hope this helped. Alley
Cracks in the top
nice solution should work, and yes bad design by coleman. you can also paint roof with camper roof paint silver with fiber
Not finding what you are looking for?