American Standard Cadet 3 FloWise 2403.128.222 Linen One Piece Toilet with - Page 2 - Answered Questions & Fixed issues

I think it's not a wise decision to clean a toilet fill valve, rather than buy a new toilet fill valve and replace with the old one. Thanks.

no reset on motor ( that would not cause breaker to trip, suspect heating element, or motor is bad.

How to Change Toilet Seat This Old House

Company web site - fill in zip code - https://www.americanstandard-us.com/parts-support/where-to-buy/product?productid=c76e85c8-571d-4992-bfd0-7d873c149285 Online retailers such as Amazon.com https://www.americanstandard-us.com/parts-support/where-to-buy/online-retailer/preferred

Yes you can replace the handles as they are available from American Standard, directly. Go to their web site, parts and service, and select you mod. toilet. Order from them. https://www.americanstandard us.com/bathroom/toilets-category

First, make sure the water feed to the tank is wide open, then make sure you have the inner workings set at maximum water level.

Hey. Not sure what model you have, but I assume you're trying to light the pilot. Remove the metal outer and inner (if applicable) cover(s) located at the bottom below the control box. with a flashlight, you should be able to locate the "thermocoupler" -that's a very thin metal tube about the thickness of cooked spaghetti. It should come from the controller and bend around a little until it ends in mid-air. That's where the pilot flame will first appear when you light it, and it should be always on, or else you will need to follow the instructions on the outside of the heater to do so. BTW: while the pilot should always be lit, the main flame (which heats the water) will only "fire" like a gas cooking range when the water in the tank starts to get cold - so don't expect to see any big flames any time you look. When you re-light the pilot, though, and turn the control dial to "hot", then you will both see and hear the flame fire up. Follow those lighting instructions VERY carefully, or the pilot won't stay lit (like, if it says to hold a button for 60 seconds, make sure you don't cheat). Good luck, hope I answered your question.

have the valve seat rubber replaced

Run a short snake thru the line. Somewhere between the drain and the tee into the line with the sink is a clog.

Be sure to pull the plunger all the way up when diverting the water between the the tub and shower if ti keeps giving you a problem it's faulty

depress and release button and whirlpool will stop

It's possible you installed the valve upside down, all values should be labeled in some way marking either hot and cold or it will say the word up where the riser tube port for the shower head is. If that's not the case remove the tub spout and check for any obstruction sometimes during tile or constructing debris can get into the pipe for your tub spout. Lastly the diverter on the tub spout could be bad. Try a new tub spout

Trey, motor or pump is seized, have tech. take a look and repair.

1. Turn off the water at the shutoff valve, flush the toilet and hold down the handle. There may be a little water left in the bottom of the tank, but don't worry about it. Wipe the flapper seat with a clean cloth to make sure it's free of debris, and check it for cracks or splits (Image 1).

   How to Fix a Leaking Toilet ' how-tos ' DIY

   www.diynetwork.com/how-to/.../how-to-fix-a-leaking-toilet DIY Network
   Feedback

How to Fix a Leaky or Runny Toilet - This Old House

www.thisoldhouse.com > ... > Toilets
This Old HouseA toilet that leaks or runs is an easy homeowner fix-if you know how to diagnose the trouble. ID parts and problems with this handy guide, and hit the hardware ...

page tite

General Plumbing Supply has always come through for me... Yelp only gives them a 3/5 but I have always had to wait with PROFESSIONALS to get my turn. I'm not big on ambiance when hunting for obscure plumbing parts.. BRING your old (always... any-parts) seat with you! Amazon says $34 (plus tax)... Phenomenal return policy A quick search on line yielded lots of other choices... Happy hunting!

Change the flap in the flush container.

The new toilet has more flushing volume than the old one. The system should handle this. The problem could be the vents on the roof are plugged or something in the line is obstructing the flow. You will need to contact a plumber

This is called air hammer, most times this is caused by vibration when a water pipe is too close to a support board you can put in a hammer arrester or make sure pipes are away from support board .

This can answer only by checking the system. Call another plumber.