20 Most Recent Moen 3175 Legend One Handle Shower Faucet With trol Pressure Balancing Valve.... - Page 8 Questions & Answers

here is a link to instructions. If this does not help call moen copy and paste https://assets.moen.com/shared/docs/instruction-sheets/ins1226f.pdf

Check the aerator, or replace it could be plugged

you can try to tap handle loose and pull up on it to remove crew. Personally I would change faucet and supply lines, and not not look back.

Check the power to it, battery or transformer unit. Ensure that the data cable and power source cable (battery pack or AC adapter) are plugged in tight and secure. Check Batteries: If using a battery pack, ensure the batteries are installed correctly and are snug in the battery holder. Loose batteries can cause the faucet to operate erratically. Sept 24, 2020

Sensors Not Working - Moen Solutions

https://solutions.moen.com > Article_Library > Sensors_N... A

moen dot com go there the manual for it is there, all mine are. some are very tricky, RTM read the manual costs ZERO to read. and is best for sure if tools are needed, or other odd things. no 2 valves on earth are the same zillions, models unless are.

you either do not have it seated all the way or you have damaged an o-ring anytime you are putting togethr parts with o-rings you should make sure and put stem grease on the o-rings to ensure not to cut or damage them. if you have damaged the o-ring instead of a whole new part you can take the o-ring out take it to your local hardware store and match it with a new one. dont forget the stem grease.

Look around in the box and your work area it sounds like the rubber seal is not in the connector.

I have no experience with modern quarter-turn taps as I prefer the ease and economy of traditional tap washers. I do have lots of experience with O rings of various types. Most commonly O ring breakage is due to the wrong size being used - diameter and/or section. when machined metal parts are fitted together and sealed with an O ring the clearance between the parts is very small - just enough to allow a sliding fit. The O ring(s) generally locate in a groove, sometimes on the end face but mostly around the diameter. O ring sizes are chosen to completely fill grooves on the end face without either stretching or compressing the rubber. Grooves around the diameter require similar consideration though some stretching is needed to assemble them; once fitted the rubber should not be under either tension or compression. The chosen section of the ring will allow the groove to be filled when the components are fitted together therefore when they are separated it will seem the O ring is too thin for the groove. If the correct size is used with carefully machined components and suitable lubrication applied during assembly there should be no difficulty. O rings are available in a number of different materials from soft natural rubbers to fairly hard synthetic materials. I suggest you carefully measure the components and compare your results with the supplied O rings.

Email moen with the part number and picture if poss they should post at kit out to you

Buy some plumbers putty.

check moens website for instructions

Go to moen.com custom support and you can look up your faucet there. If it is discontinued they will help you with a replacement..

Moen.com will have everything you should need.

In all honesty the easiest fix is to call moen and they will and they will send a new faucet to your door step with no charge. It is a cartridge you have to replace inorder to cure the leak. It a moen cartridge part # 1224 should you choose to replace it. Assuming this is a Monticello 2 handle faucet. Hope this helps!

contact moen for replacement parts. have your model number ready

Yes moen do life time warranty contact moen and they will send you one out

You Should replace with new design think

check the faucet itself for clog or damage

look on YouTube for videos

First clean out your cabinets under the sink. Second turn turn the cold water valve off, hot water valve as well.
You should be able to locate the sprayer hose as it will have a weight on it, this helps to pull the sprayer back when you are finished with it. Remove the weight by lifting up on the tab should be on the center of the weight.
Then you should see the hose connection.There you should see a button.Push it in and give it a little tug. The hose should be disconnected. Just follow in reverse order to reinstall.
I hope this is information is helpful. Have a blessed day.