Top 20
Jacuzzi Signa 6 Whirlpool JAC-B540... - Page 8 Questions & Answers
I need to manual and installation instructions for
Hello - best suggestion would be to get the make / model # and serial # go under google punch this information in, you will find contact #s,that is how we find out a lot of contact information needed.Sorry could not be of more help.
5/18/2011 10:35:10 PM •
Jacuzzi Home
•
128 views • 0 helpful votes
I have a Jacuzzi tub and the vacuum switch will
if when you push the air button it will not turn off the pump, it may be the button that is bad on the top of the tub or the air switch located in the motor.
take the pump out and plug it into an outlet. get a straw and blow into the air switch with the pump plugged in still. if it comes on then the button on the top of the tub is bad. if it doesn't come on then the air switch is bad.
2/16/2011 11:58:12 AM •
Jacuzzi Home
•
1,528 views • 2 helpful votes
Toilet does not flush clean.
Welcome to the world of 1.6 gallon flush toilets. You have already done everything that can be done to help the problem and no you are not the only people having this problem. This is just the beast!
They have had this problem with these 1.6 flush toilets from the get go and have come out with power flush toilets to fix this but hold on to your wallet. There are some toilets out there that work better without the power flush made buy American Standard and Kohler but they will run you more then the Jacuzzi.
Sorry I wish there was a better answer to this.
3/23/2011 7:49:44 PM •
Jacuzzi Home
•
377 views • 0 helpful votes
My mother has a Jacuzzi
*********** has a Jacuzzi Perfecta.
This came in two models... one with a round bowl, the other with an elongated bowl.
Both of them use the BN30 BN31 tank.
If you have trouble tracking down a gasket, you might try using plumbers' putty.
Be aware, though, that there have been reports of the back of these tanks cracking. Check the tank to ensure that the leakage is coming from the gasketed surface, and not from a crack.
Good luck!
3/3/2011 12:45:26 AM •
Jacuzzi Home
•
330 views • 0 helpful votes
Toilet does not stop filling,
Hi,
Replace your toilet fill valve with a fluidmaster 400A
Click herehttp://411plumb.com/how-to-replace-your-toilet-fill-valve-with-a-fluidmaster-400a
heatman101
1/16/2011 10:19:55 PM •
Jacuzzi Home
•
1,138 views • 0 helpful votes
The toilet bowl never stays full of water? It
I have the same problem with my Toto TS703. When you flush it, it fills the bowl with water to the rim and stops. Within an hour, the water in the bowl is totally empty except for a small puddle. This has been going on for a few days. It was installed 3 years ago and never had a problem with it until now.
3/21/2011 12:49:35 AM •
Jacuzzi Home
•
179 views • 0 helpful votes
One of the jet assemblies
once a jet face has fallen out of a hot tub that means the insert has failed and is broken. you will need to locate a new jet insert. Jet inserts have little tabs on them that hold them in place and when they get worn out the jet face will fall out into the tub.
1/29/2011 5:00:32 PM •
Jacuzzi Home
•
624 views • 1 helpful votes
I have a regular size bath tub with a jacuzzi with
First of all make sure you have the tub filled with water to a level above the jet inlets. They normally have a sensor to prevent the tub from starting dry.
Next, check and reset any GFCI electrical receptacles that might be on the same circuit as the tub. They are the wall receptacles that have the 2 little buttons in the middle. Look in the bathroon, adjacent bedroom, closets etc.
The only other thing you can really check on your own is the air tube leading to that metal switch on your tub. The switch is not electrical for safety, it is a little air pumper with a plastic hose attached to it leading to an air powered actuator on the pump. Sometimes the hose dries up / comes loose / falls off. Check if there is an access panel on the tub where you can look inside and see if the plastic hose is still attached at both ends. You might even be able to unscrew the metal switch cover and lift it up and see from there. Otherwise try fpumping the metal switch (firm repeated pushing) to see if that will activate the pump. If that does the trick then it is probably just a loose connection / leak on the air hose such that it is not quite airtight.
Good luck and please comment back if this was at all helpful or if you need further assistance.
Thanks.
Joe.
2/13/2011 4:09:55 PM •
Jacuzzi Home
•
397 views • 1 helpful votes
On off switch isnt working,i
When you push the air button and nothing happens it could be the air button is bad or could indicate the air switch in the motor is bad.
pull out the motor and plug it into a wall outlet. take a straw and push it onto the air switch, where the air tubing was connected, and blow into it.
if the pump comes on then you will need a new air button on the top of the tub. If however it does not come on then will need the air switch that is on the motor to rectify the problem.
2/8/2011 1:45:06 AM •
Jacuzzi Home
•
407 views • 3 helpful votes
Replace the existing gold hardware
There are no easy answers to this. You will need to go out and find the handle you want and the find a seat with matching hinges. Your best place will be a Plumbing supply house that can order matching hardware for you. This will let you pick just what you want and it will all match. I'm sorry but I don't think your local hardware store will do.
3/19/2011 11:56:56 PM •
Jacuzzi Home
•
135 views • 0 helpful votes
We use our jacuzzi once
the problem is bacteria building up in the water lines once the water
dries. You should be using a jet cleaning product to clean the water
lines out before they dry.
We have several different good
cleaners on our site that all work well at keeping bacteria out of your
water lines.
You can click on the link below and it will show you
what is available.
Jet cleaners
2/16/2011 6:41:22 PM •
Jacuzzi Home
•
282 views • 0 helpful votes
Tank fills very slow
maybe it's a problem with the water pressure. you should get a plumber or contact the water company
3/8/2011 5:17:40 PM •
Jacuzzi Home
•
103 views • 2 helpful votes
1980's jacuzzi bathtub, won't turn on (seems to be
you will need to open up the back of the tub where the pump is and see if there is a clear tube about 1/4" OD attached to the backside of it close to the pump cord.
If it is there then you will need to check out the air switch on the motor that the air tubing attaches to to see if it is good. If it will activate the pump when you blow into it with a straw then the air button on the top of the bathtub is probably bad and needs to be changed. if it does not turn the pump on/off when you blow into it then you will need a new air switch.
1/23/2011 3:22:18 AM •
Jacuzzi Home
•
313 views • 0 helpful votes
Not finding what you are looking for?