Top 20
Jacuzzi Signa 6 Whirlpool JAC-B540... - Page 6 Questions & Answers
I set the temp to 75 then the spa show 108 and set
This sounds to me like one or both of the sensors on your spa may be bad and need replacing.
There are two sensors in each hot tub. One for the temperature of the water and a high limit to prevent the water from going over 112 degrees.
If one of these is bad then the sensor will not read the correct water temperature.
Rod
US Parts Center
8/22/2013 1:10:54 AM •
Jacuzzi Home
•
200 views • 0 helpful votes
Tank takes a long time to fill
check for a clog in the toilet valve supply as the washer can deteriate or the old piping in the house can clog if they are old and made of galvanize pipe or the fill valve is clogged. replace valve and or fill valve in the tank
8/3/2013 5:47:31 PM •
Jacuzzi Home
•
199 views • 0 helpful votes
Breaker trips on startup
If your circuit breaker is tripping when you turn the pump on it is caused by a bad motor. The motor probably has a short in it causing the breaker to trip,Replace your pump and that should solve your problem with the breaker.There is an outside chance you may have a bad circuit breaker too.US Parts Center
9/2/2013 3:39:51 AM •
Jacuzzi Home
•
89 views • 0 helpful votes
Onga spa master
What is the nature of your question?
Rod
US Parts Center
8/14/2013 11:22:42 PM •
Jacuzzi Home
•
95 views • 0 helpful votes
Power button pushs in and doesn't start
If you press the air button in and it does not turn the pump on you need to check a couple things.
- Is the circuit breaker on
- is the hose still attached to the bottom of the air button and the air switch on the pump
- check the air switch in the motor - it probably needs to be changed.
US Parts Center
8/26/2013 1:53:13 AM •
Jacuzzi Home
•
60 views • 0 helpful votes
What red light flashing codes
the motor has probably seized from rusted bearings. check pump for problems. possible failure of capacitor for motor.
6/22/2013 11:56:25 PM •
Jacuzzi Home
•
169 views • 0 helpful votes
How do you replace a jacuzzi air switch
The air switch used in jetted tubs is mounted in the box on the bath pump.Remove the pump from under the tub and take the top of the little box off by removing the two screws holding it in place.Once the screws are removed you may lift the lid off and you will see two wires going to the air switch, one wire coming from the pump power cord and the other from inside the motor.Remove the two wires from the air switch and then remove the air switch from the pump by taking off the nut that holds the air switch in place.Reinstall the air switch by putting the two wires back onto the air switch and put the cover back on the box on the motor.rodus parts center888-521-6183
4/6/2013 4:21:10 PM •
Jacuzzi Home
•
1,271 views • 2 helpful votes
Hot tub won't come on
Start at the spa.
- Do you have voltage coming to the terminal strip in the control box?
- Is it the correct voltage?
- Do you have voltage at any point after that?
- Is there power coming out of the transformer?
these are the starting points to determine if you have a bad circuit board or a bad transformer.Rod
US Parts Center888-521-6182
3/27/2013 11:27:02 PM •
Jacuzzi Home
•
203 views • 0 helpful votes
Circuit braker keep popping
Sounds like the heating element has gone out again. Once you reset the circuit breaker and the tub turns on it will start to circulate the water. This usually runs like this for about 2 mins and then the tub will recognize it is cold and send power to the heater. If the element is back at that point it will blow the circuit breaker.If this circuit breaker pops as soon as you turn it on then you most likely have a bad circuit board.Rod
www.uspartscenter.com
1/30/2013 11:36:24 PM •
Jacuzzi Home
•
575 views • 1 helpful votes
Hot water is very slow coming out spout. Cold water comes out fine with good pressure..
the anti scald is adjusted too low. its located under/behind the handle. it usually has am allen wrench head. remove the handle and adjust it all the all the way to hot that should fix it. on some models you can remove the entire thing,but on some that will cause the handle turn 360deg because in some models its also the stopping point of the handle. hope this helps
12/11/2012 2:02:56 AM •
Jacuzzi Home
•
741 views • 1 helpful votes
J315 lights flickering
Check the connections of the light bulb and any connecting wires. Short of this you may have a faulty transformer.
Rod
US Parts Center
2/11/2013 6:47:22 PM •
Jacuzzi Home
•
75 views • 0 helpful votes
My jacuzzi motor is not working
When you push the button and the motor does not turn on there a couple of things to check.Is there power to the pump? check the circuit breakerIf there is power to the motor then the air button on the top of the tub may be bad or it could be the air switch inside the motor.Rod
US Parts Center521-6183
1/11/2013 6:55:57 PM •
Jacuzzi Home
•
147 views • 0 helpful votes
Not finding what you are looking for?