Top 20 Jacuzzi Signa 6 Whirlpool JAC-B540... - Page 5 Questions & Answers

Try this link

There is a very good chance there was a factory defect. Either the exit hole is misshaped or there may be a small sharp edge that could be eating up the flappers. I would contact the manufacturer telling them about your problem and see if they will replace the tank or just buy a bunch of flappers wholesale and change them when needed. good luck

If your hot tub water has all drained then you need to look for a leak obviously. Start in the cabinet area where there are unions attaching the pump and the electronics. Sometimes those will vibrate loose and will begin to leak. If all the unions are tight and you see no water then you need to start to look elsewhere around the tub for water leaks. It could be a broken manifold in the plumbing or a jet body. Rod US Parts Center

While the brand of the tub may be of importance to you it may not be important when finding parts for it. Bath tub manufacturers do not make anything that goes into their tubs i,e. the jets, pumps and controls are all purchased from various Mfg. Are you have any particular problems with either unit that would make you need the brand of either? Rod U S Parts Center

The air button is located on the top lip of the bathtub or just below the top lip on the sidewall. It is held in place by a nut that is threaded up the length of the air button body. In order to change the air button you will need access to the underside of that air button so the nut can be unthreaded off the button body. Rod US Parts Center

When you installed the new jet, did you install a new gasket on the wall fitting or use 100% RTF type silicone? In order to seal a wall fitting that is cracked an leaking, the replacement must have either the gasket or silicone to seal the wall fitting against the wall of the tub or it will leak when filled with water. Rod U S Parts Center

What kind of switch are you referring to? Rod US Parts Center

Hi, Go to amazon and look for replacement parts.... here: Jacuzzi SWP2959 Perfecta Dual Flush Two Piece Elongated Comfort Height... I hope this was helpful. Mike

get it checked by electrician. there has to be an access panel.

Curios, why did you order another control panel? I need some history, when it worked, how it failed, any other information like if it was moved or rewired for power...etc.

If your hot tub is running but NOT heating then you need to look at a couple of things.First, on the topside, is the heat indicator light on?If it is on and the tub is not heating then the temp sensor or the high limit sensor is not working and need to be replaced.US Parts Center

Bath Panels can be very difficult to locate. I would check with your local Jacuzzi Showroom first. If they are unable to locate the panels you need or they are no longer made then you should head over to Lowes or Home Depot to get a generic panel from one of them and you may need both panels replaced so they match. rod US parts Center Bath Spa Replacement Parts Hot Tub Bath Parts Accessories US Parts...

This actually sounds like you have some calcium built up on the inside of the air button.Take the trim ring off the air button and pull out the center button.Get some soft emery cloth and run it around the outside of the center button and well as the inside of the button body then reinstall. That should solve your problem with a sticking air button.US Parts Center

FL is a "flow" issue. Check the filter to make sure it is clean. Start by removing it from the tub and see if that solves the error. The next item to check is the gate valves to make sure they are open all the way. There are usually one on either side of the pump and control box. Rod US Parts Center

fill the tub and run a cycle of 10 min to clean the system. \now fill fresh water and use .

Drain plugs on bathtubs are generic in size. Jacuzzi does not make them. They are made by other Mfg and installed by your local plumber when the tub is installed. US Parts Center

The Air Tubing presses onto the little nipple on the underside of the air button. There is no seal on this set up. Once the air hose is attached to the nipple there should no air leakage when the air button is pressed.Before you install the air hose you might cut off half inch on the end to make sure the end has not splits and you get a good piece of hose so it will seal properly.US Parts Center

The hose under your tub attaches to the bottom of the air button and to the air switch located on the back of the pump or on the box on top of the pump. US Parts Center

Check the air intake and see if it is ok. Check the output side of the airpump too and also make sure that the nozzles in the tub are not screwed down to shut them off.

Take the unit off of the tub and see if there is a seal there,if there is a seal there try putting some silicone caulking around the seal or where the seal would be and then put the unit back together but don't over tighten the unit until the caulking is cured(24hrs) and then tighten the unit back up and this should seal it back up,unless the water is leaking past the actual switch itself,then you will need to replace this switch!Good Luck!!