Top 20
Jacuzzi Signa 6 Whirlpool JAC-B540... - Page 4 Questions & Answers
Why is my jacuzzi toilet not flushing properly
First try yourself for checking internal part where some particle stuck inside the flush or check the flush for how much water coming from the pipe if not found properly then i suggest A-general plumbers for best services they handle this type of issue easily.
http://www.a-general.com
7/27/2014 10:00:10 PM •
Jacuzzi Home
•
915 views • 0 helpful votes
Leaking at jet to tub connection
You can fix that with a small amount of "plumber's putty". You have to remove the jet from the tub first, then smear the plumber's putty around the junction where the two meet each other, then reassemble.
8/4/2014 9:34:31 PM •
Jacuzzi Home
•
142 views • 0 helpful votes
When I push the start button motor running but not stay on
Air Switch Repair
It sounds like you have a bad air switch located in your motor.
The air switch is what the air hose connects to on the back of the motor or on the box on top of the motor. The other end of the air hose is connected to the air button on the lip of the tub.
This is a latching air switch and when you push the air button it latches to send power to the motor. When the air button is pushed again it opens the latch in the air switch and stops power going to the motor shutting it off.
US Parts Center
5/30/2014 9:34:20 PM •
Jacuzzi Home
•
772 views • 1 helpful votes
Water continues to run problem
Could be a stuck or old and leaky flapperCould be a clogged valveCould be an old in need of replacement valveCould be a number of other things depending on what kind of toilet and hardware you haveResidential or commercial? Ball cock and flapper? Or newer style internal float valve?
8/5/2014 4:26:29 PM •
Jacuzzi Home
•
119 views • 0 helpful votes
We bought an elongated smooth sided Jacuzzi toilet and it is leaking clean water from the back toward the wall
Could be a few issue. First check at the back where the tank sits on the bowl, reach underneath or look with a flashlight if you can to see between the tank and the bow, pay attention to the bolts in particular, if you see any water dripping down the bolts or between the tank and the bowl, the tank to bowl gasket ir bowl gasket bolts are leaking, and need to be replaced. Also look inside the bowl when its flushing, no water should be splashing up over the edge of the tank. Also inspect underneath the fill valve that gasket could also be leaking, or the supply line could be leaking.
7/12/2014 10:34:20 PM •
Jacuzzi Home
•
195 views • 0 helpful votes
Jacuzzi tub will not turn on button will not click on as usual
Your problem is most likely NOT the air button but the switch in the motor.
Air Switch Repair
It sounds like you have a bad air switch located in your motor.
The air switch is what the air hose connects to on the back of the motor or on the box on top of the motor. The other end of the air hose is connected to the air button on the lip of the tub.
This is a latching air switch and when you push the air button it latches to send power to the motor. When the air button is pushed again it opens the latch in the air switch and stops power going to the motor shutting it off.
Rod
US Parts Center
4/10/2014 11:40:23 AM •
Jacuzzi Home
•
877 views • 2 helpful votes
How to install whirlpool jacuzzi switch
Air Switch Repair
It sounds like you have a bad air switch located in your motor.
The air switch is what the air hose connects to on the back of the motor or on the box on top of the motor. The other end of the air hose is connected to the air button on the lip of the tub.
This is a latching air switch and when you push the air button it latches to send power to the motor. When the air button is pushed again it opens the latch in the air switch and stops power going to the motor shutting it off.
US Parts Center
4/27/2014 9:12:59 PM •
Jacuzzi Home
•
465 views • 0 helpful votes
How to pull off the knobs
On most bath fixtures the knobs or handles are held on by a discreet screw set screw. If there is a plastic or rubber "button" in the center of the knob, gently pry it from the edges to remove it and there should be a machine screw going through the knob holding it to the valve stem. Remove the screw and the knob should come off. Sometimes requires some light tapping from the back side. If this doesn't appear to be the case, examine the back side of the knob to see if there is a set screw in a small hole going in sideways effectively clamping the knob to the stem. Often times this type will require a very small Allen wrench. Be sure to use the correct size or you will strip out the hex shaped opening and then will require drilling out. This is not what you want to be doing!
5/30/2014 12:32:39 PM •
Jacuzzi Home
•
150 views • 0 helpful votes
Water level sensor
The 'low-water' sensor installed in a bathtub is designed to NOT allow the pump to run without water contacting it.
It sounds as if this is operating as it should.
Once the pump comes on you should be able to touch the "logo" or the on/off button to turn the pump on and off.
If the pump is not turning on/off when the tub is full of water you may be experiencing a problem with the control box under the tub skirt.
Rod
US Parts Center
888-521-6183
3/20/2014 8:39:42 PM •
Jacuzzi Home
•
846 views • 0 helpful votes
Not finding what you are looking for?