Top 20 Jacuzzi Signa 6 Whirlpool JAC-B540... Questions & Answers

possibly some seals deteriorating.. check pump and connections..

A flashing “FL1” display means the flow switch is
malfunctioning open, the filter cartridge is excessively
dirty or an “air lock” condition has occurred at the
circulation pump intake.

If there is room most definitely you can place the faucets on the tub itself. You can mount them on the left rear. However be very careful drilling the holes and make sure you have it aligned correctly before drilling. Check underneath to make sure there is enough room for clearance and hook up. Here is what it will look like.

they work on a air switch the hose might not be hooked up on one end

Sounds like the hoses to the jets are the pump are breaking down and pieces coming off. Replace the bad hoze(s).

hi there. FIrst of all be sure the water lever is above all of the jets for it to work properly. REgarding the jet where the water does not come out properly i am not sure what that means. BUT, the jet is adjustable so turn it and see if that fixes the problem. good luck.

You are on the right track. Be sure and chlorinate and run the jets at the same time I would let it set for at least a couple of hours running the jet intermittantly and then drain and repeat.
Sound like you have Iron Bacteria. You may want ot contact a water profeessional who can recommend ways of getting rid of the iron.
Properly Chlorinating your well would be a good first step.
What part of the country are you in>

sanray

Many time leaks around pumps are a simple o-ring that needs to be cleaned and/or tightened. If the jets are leaking from the back side then the jet will have to be removed and resealed.


Good Luck, Phil

Maybe these folks can help they stock allot of Jacuzzi parts.

Can't Find It?

Send us a picture Text a photo: 305-321-3420 https://www.guillens.com/catalog/shop/Jacuzzi/Bath/Repair-Parts/Control-Boxes/mfr-3BU?pagenum=1

No, replace the whole thing. That is bad design and inferior parts. Ask Moen to replace it under warranty. They might say No, but then again, they might know of a fix or if they had a bad batch of plastic parts.

Hi, Please attempt to start the jacuzzi without any water and see if it functions. Then you can fill the jacuzzi up to 1/4th with water and check if it continues to run. If so, continue to one half full. If this jacuzzi breaks down at these water levels, then you'd need to call the manufacturer to advise on what part needs to be changed to get everything working again. Thank you.

yes the are and parts are available on line.

they twist out

Hello, Several things can cause this problem- if you post a picture of the inside of the tank so we can have a good look at how the fill/stop mechanism operates that would be great. We could more than likely identify some type of problem and solution. Not all flush/fill mechanisms are not the same but thats surely where your problem is UNLESS its in your water lines. I would love to help you just please provide photos and as much information as you can. Good luck! Mr.Mike

pump -impeller failure /bearings /motor failure

There may be a video but you should be able to tell by looking at it too big screw under tank holds valve on big screw under tank holds valve on see: https://reviewmotors.co/jacuzzi-dual-flush-toilet-repair-parts

Contact the Dealer and seek qualified tech service. Risk of electric shock/***** You should not take the risk but have a QUALIFIED SERVICEPERSON perform the work.

If there is power to the unit, most likely it will need to be replaced. Check for reset button, and check the fuses before replacing the unit.

These switches that are mounted to the tub itself are usually air switches when you push the soft button it puffs air into a solenoid somewhere near the motor causing it to activate the pump, and there is a possibility that the pump motor has a reset button on the end of it to kick it off if something would cause the pump to jamb, hair,toy, jewelry or whatever that somehow got sucked into the intake

Should be one on the motor and also check to see if there is a GFCi somewhere too. Could be around where the jacuzzi switch is.