20 Most Recent Jacuzzi Signa 6 Whirlpool JAC-B540... - Page 9 Questions & Answers


Could be a few issue. First check at the back where the tank sits on the bowl, reach underneath or look with a flashlight if you can to see between the tank and the bow, pay attention to the bolts in particular, if you see any water dripping down the bolts or between the tank and the bowl, the tank to bowl gasket ir bowl gasket bolts are leaking, and need to be replaced. Also look inside the bowl when its flushing, no water should be splashing up over the edge of the tank. Also inspect underneath the fill valve that gasket could also be leaking, or the supply line could be leaking.

Jacuzzi Home | Answered on Aug 23, 2014


Could be a stuck or old and leaky flapper
Could be a clogged valve
Could be an old in need of replacement valve
Could be a number of other things depending on what kind of toilet and hardware you have
Residential or commercial?
Ball cock and flapper? Or newer style internal float valve?

Jacuzzi Home | Answered on Aug 11, 2014


Sounds like a problem with the thermostat.

Jacuzzi Home | Answered on Aug 05, 2014


You can fix that with a small amount of "plumber's putty". You have to remove the jet from the tub first, then smear the plumber's putty around the junction where the two meet each other, then reassemble.

Jacuzzi Home | Answered on Aug 04, 2014


First try yourself for checking internal part where some particle stuck inside the flush or check the flush for how much water coming from the pipe if not found properly then i suggest A-general plumbers for best services they handle this type of issue easily.
http://www.a-general.com

Jacuzzi Home | Answered on Aug 04, 2014


There is a very good chance there was a factory defect. Either the exit hole is misshaped or there may be a small sharp edge that could be eating up the flappers. I would contact the manufacturer telling them about your problem and see if they will replace the tank or just buy a bunch of flappers wholesale and change them when needed.

good luck

Jacuzzi Home | Answered on Jun 22, 2014


Air Switch Repair
It sounds like you have a bad air switch located in your motor.
The air switch is what the air hose connects to on the back of the motor or on the box on top of the motor. The other end of the air hose is connected to the air button on the lip of the tub.
This is a latching air switch and when you push the air button it latches to send power to the motor. When the air button is pushed again it opens the latch in the air switch and stops power going to the motor shutting it off.

US Parts Center

Jacuzzi Home | Answered on Jun 06, 2014


The knobs on the jacuzzi whirlpool pull off.

US Parts Center

Jacuzzi Home | Answered on Jun 06, 2014


Air Switch Repair
It sounds like you have a bad air switch located in your motor.
The air switch is what the air hose connects to on the back of the motor or on the box on top of the motor. The other end of the air hose is connected to the air button on the lip of the tub.
This is a latching air switch and when you push the air button it latches to send power to the motor. When the air button is pushed again it opens the latch in the air switch and stops power going to the motor shutting it off.

US Parts Center

Jacuzzi Home | Answered on Jun 06, 2014

Not finding what you are looking for?
Jacuzzi Signa 6 Whirlpool  JAC-B540... Logo

Popular Tags

22 questions posted

Ask a Question

Usually answered in minutes!

Top Jacuzzi Home Experts

US Parts Center
US Parts Center

Level 3 Expert

719 Answers

Mike

Level 3 Expert

4357 Answers

john h

Level 3 Expert

21326 Answers

Are you a Jacuzzi Home Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Jacuzzi Home

  • Jacuzzi Home

Most Popular Question

jacuzzi hot tub model j 300 series fl 1

  • Home
Loading...