20 Most Recent
Jason Natural Cosmetics Jason Designer EM630 Rectangular 72" x 36" x 20.5" Combination Air-Whirlpool - Page 7 Questions & Answers
After the Summer Time change the clock keep running without adjusting to the real time?
Question edited for clarity.
Questioned moved from Misc to clocks.
All questions need full 'make model (what it is)' as the first three words or it is all guesswork.
My guess is that you are in the wrong time zone and it will change in 2 weeks when it changes in the UK. You are set to GMT instead of PST, CT or EST.
..
3/18/2023 7:26:49 PM •
Home
•
Answered
on Mar 18, 2023
MY Ecco 55 Dims the moment i turn it on.
If it dims as soon as you turn it on, then it could be a sign of a faulty power supply or a loose connection. You should check the power supply and connections to make sure everything is secure and functioning properly. If the issue persists, you may need to contact the manufacturer for further assistance.
3/16/2023 10:01:20 PM •
Home
•
Answered
on Mar 16, 2023
I have a Bulova B1987 mantel clock. I bought it in December 2022. It is now March 2023 and it has stopped chiming. It keeps perfect time, just won't chime.
There are a few potential reasons why your Bulova B1987 mantel clock has stopped chiming:
- Check if the chime switch is in the "on" position. If it is not, switch it to "on".
- Make sure that the clock is wound fully. A clock that is not fully wound will not chime.
- Check if the chime melody selector is in the "off" position. If it is, move it to a melody position.
- If the clock has been moved or bumped recently, the chime hammers may have been knocked out of alignment. This can be fixed by a professional clock repair person.
- The chime rods or hammers may be damaged or worn out. This can also be fixed by a professional clock repair person.
If none of these solutions work, it may be best to contact a professional clock repair person for assistance in fixing the clock's chime.
3/4/2023 10:11:58 AM •
Home
•
Answered
on Mar 04, 2023
Having problem with wireless smoke detector on my NX-8. Is deleting current program and reprogramming the way to go?
Before deleting the current program and reprogramming your NX-8 wireless smoke detector, you may want to try the following troubleshooting steps:
- Check the batteries: Ensure that the batteries in your wireless smoke detector are not dead or low. Replace the batteries if necessary.
- Check the signal strength: Make sure that the wireless smoke detector is within range of the NX-8 control panel. You can try moving the detector closer to the panel to see if it helps.
- Check for interference: Interference from other wireless devices, metal objects, or thick walls can affect the signal strength. Try removing any potential sources of interference or relocating the detector.
If these steps do not resolve the issue, then deleting the current program and reprogramming the wireless smoke detector may be the next step. Be sure to follow the instructions in the NX-8 programming guide to properly delete and reprogram the detector. If you are not comfortable with programming the system yourself, you may want to contact a professional alarm company or technician for assistance.
2/25/2023 6:37:34 PM •
Home
•
Answered
on Feb 25, 2023
Plumbing - Perrin & Rowe U.5383 Shower Head Diverter - how remove spindle?
Unfortunately, without being able to see the spindle, it is difficult to provide specific instructions on how to remove it. However, in general, you should be able to remove the spindle by unscrewing it from the housing. You may need to use a pair of pliers or a wrench to get a better grip on the spindle. Once you have loosened the spindle, you should be able to pull it out of the housing.
2/22/2023 9:39:37 PM •
Home
•
Answered
on Feb 22, 2023
Fashion Bed Group Bunk Bed
You can purchase the long black screw assembly from the manufacturer of the Fashion Bed Group Bunk Bed. You can contact them directly to inquire about purchasing the part.
2/22/2023 9:37:58 PM •
Home
•
Answered
on Feb 22, 2023
Chime on my Daniel Dakota Grandfather clock does not work
If the chime on your Daniel Dakota Grandfather clock has stopped working, it is likely due to a mechanical issue. You may need to take the clock to a professional clock repair shop to have it serviced. The repair shop should be able to diagnose the issue and make any necessary repairs.
2/22/2023 9:36:27 PM •
Home
•
Answered
on Feb 22, 2023
What is a pill dispenser?
The medicines should be taken in the right amount and at the right time. Due to memory problems the seniors are not able to take in a right way, so a
medication dispenser for seniors can be a good solution for that. A pill dispenser contains all the medication details along with scheduled time details.
2/21/2023 4:35:42 AM •
Home
•
Answered
on Feb 21, 2023
I need a manual for my marco indoor fireplace model#792775D because i am trying to light it
I am not a service professional, but just a homeowner who has some experience with this gas log.
GAS LOG INSTRUCTIONS
Brand: Marco Gas Log (company is now out of business)
#792775, unvented gas log
Installed late 1990's when house was built
The gas is turned on and off using the key on the wall to the left of the fireplace. The gas is OFF when the key is turned as far clockwise as possible. Turn the key counterclockwise about a half turn or whole turn (180 degrees to 360 degrees) to light the pilot and turn on the log. You don't have to worry about gas coming out into the room before you light the pilot, or if the pilot goes out.
Horizontal as far clockwise as possible = OFF
Vertical ½ turn = ON
The log needs to be cleaned before using at the beginning of the season. Remove the logs, taking note of their position so you can replace them the same way. Use a toothbrush to clean the thermocouple, which looks like two little wires immediately to the right of the pilot (which looks like a metal tube that is located in the center just in front of the back log). Use a vacuum cleaner hose and duster to clean dust off all metal parts and the fire box interior. You can go ahead and replace the back log before lighting the pilot.
HOW TO LIGHT THE PILOT:
With the gas turned on with the key on the wall, find the black and white knob on the lower right of the gas log and turn it all the way to the right (clockwise) to the to the right as far as it will go, then turn it back ever so slightly to the left until you feel a little resistance (like a click that you feel rather than hear). The pilot cannot be lit when turned all the way to the right.
Push the knob in with your thumb and use your other hand to light the pilot with a long-stem lighter or match. Hold the knob in for at least 30 seconds. The thermocouple has to be hot before the pilot will stay on. Let the knob come out very slowly. Hopefully the pilot will remain lit, but if it does not, you will need to repeat the procedure until it does. Be sure to hold the knob in until the thermocouple is hot and release the knob very carefully. When the pilot stays lit, then turn the knob to the left counterclockwise until the flame stays lit and carefully place the logs back into their original position. Note: Push the knob in only when you are actually lighting the pilot, not while you are turning the knob.
Set the thermostat from Hi to Low as pictured on the knob. Once the log is lit, it should stay on until the thermostat causes it to go off. Hopefully the pilot will stay on so that the log will come back on automatically according to the setting of the thermostat (from low to high). It will be at its hottest when the knob is all the way counterclockwise.The flame will go off and on according to the temperature in the room. The pilot should stay lit even when the main flame goes out, as shown above.
2/10/2023 8:03:19 PM •
Home
•
Answered
on Feb 10, 2023
La Crosse Model 40222 analogue clock. How do you charge a lithium battery for the WALL CLOCK please?
Question edited for clarity, and add MAKER, so few words, so many spelling mistakes!
Lithium batteries aren't rechargeable. Your small round CR2032 battery lasts 8 years. It is the same battery in a computer motherboard and easy to find in any pharmacy.
REPLACING 3V LITHIUM BATTERY The Auto-set time memory is maintained by a lithium button cell battery, model CR2032. The expected life of this battery is about 8 years. Be sure that the 2 "AA" batteries in the clock are fresh. The MODE switch (8) must be in the RUN position when replacing this button cell battery. This battery is located in the small round battery compartment on the rear of the clock secured by a screw. Open the battery compartment (3) with a screw driver and replace the CR2032 lithium battery observing the polarity. Then close the compartment securing with the screw.
https://cdn.shopify.com/s/files/1/0035/7443/1790/files/40222s-40222b_1.pdf?v=1594066127
..
2/8/2023 3:21:47 AM •
Home
•
Answered
on Feb 08, 2023
Not finding what you are looking for?