20 Most Recent Pride Jazzy 1103 Ultra Standard Power Chair - Page 4 Questions & Answers

Recharageable batteries need to be kept charged and if left uncharged for a long period they most likely no longer work.You need to replace these batteries.

If it has a distinct odor like a cat box, it likely is just 80W85 axle lube. If no distinct odor, dip a cotton swab in to see if it has a dye color- if no dye color and it is brown, 20 or 30 weight non detergent oil should be fine. If it is red like automatic transmission fluid, and smells like transmission fluid, it probably is.If unit is less than one year old double check with the vendor to see if there is a warranty issue. if it is several years old, there is no warrnty to worry about.

Hello,download:SHOPRIDER SERVICE MANUAL 2007 1-800-743-0772.Save as a PDF File to read via an Adobe Reader.Hope this was of help,Colin.

When the power seat lift lowers down, there is usually a bracket that pushes a button under the seat that tells the motor the seat is lowered and the power chair is safe to operate. Sometimes the bracket can get bent and the button does not get pressed when the seat goes down. Check under the seat around the seat post for the button and make sure the bracket is connecting to it. Carefully bend it back into place if it is not hitting the button properly. If the bracket came off, it will need to be replaced.
Good luck!

the 7 lights indicate a joystick problem which means the joystick/controller will have to be replaced since there is no self repair fix Unless you can locate a good used joystick/controller for cheap (around $600.00 rebuilt) I would return the chair and get my money back Hope this helps

Relace your batteries and your problem should go away hope this helps

You can visit this website to find answers on what the flashing trouble indicator lights mean: http://www.pgdt.com/scenter/diagnostics/diagvsi.html
Locate the page that has the controller used on your power chair/scooter and count how many lights are flashing to diagnose the trouble. If your insurance purchased the power chair for you, they may also cover the repairs; contact them for information.
Good luck!

If you have a vsi joystick seven bars means there is a possible joystick trip
a joystick trip is indicated . Make sure the joystick is in the center postion before switching on the VSI.
It may also be locked try this.

LOCKING/UNLOCKING THE VSI

The VSI has a feature that enables you to lock your power chair to prevent

unauthorized use.

To lock the VSI:

1. With the VSI powered on, press and hold the on/off key. After one (1)

second, the VSI should beep.

2. Release the on/off key.

3. Push the joystick to the full forward position until the VSI beeps.

4. Pull the joystick to the full rearward position until the VSI beeps.

5. Release the joystick. There should be a long beep.

6. The VSI is now locked.

To unlock the VSI:

1. Press the on/off key and power on the VSI. The maximum speed/profile
indicator should ripple side to side.

Good Luck

mimobility

LOCKING/UNLOCKING THE VSI

The VSI has a feature that enables you to lock your power chair to prevent

unauthorized use.

To lock the VSI:

1. With the VSI powered on, press and hold the on/off key. After one (1)

second, the VSI should beep.

2. Release the on/off key.

3. Push the joystick to the full forward position until the VSI beeps.

4. Pull the joystick to the full rearward position until the VSI beeps.

5. Release the joystick. There should be a long beep.

6. The VSI is now locked.

To unlock the VSI:

1. Press the on/off key and power on the VSI. The maximum speed/profile
indicator should ripple side to side.

Good Luck
mimobility

Hi Jack
Sounds Like all you need is for a technition to program you chair. They can do an adjustment to compensate the different strengths of each motor and make the chair run straight Also to improve the turning speed adjustments. Programer is a P&G PP1


Good Luck

mimobility

2 U1 batteries are what you need hope this helps

ana at the top of the joystick is the on/off button just push it and the lights sshould come on the battery level lights should all light up and you can set the speed with the two buttons on each side the left to slow down and the right to speed up. When all the speed lights are lit you are at max speed Hope this helps

Hello mmcpowers,

For the Pride Jazzy wheel chairs you can locate what you need at the Jazzy website at the following link http://www.thescooterstore.com/products/product_manuals.aspx
When on the site you will locate the chair you need and the wire diagrams are in the owners manuals. As a common problem is just a plug coming un-wired they tell you where they are and the wire configuration. If you tell me some of the other chairs you are dealing with I will try and locate the website for them as well.

Thank you for choosing FIxYa.com

Well you don't need a 24 volt battery you will need 2 12 volt batteries for a total of 24 volts Contact any local Battery distributor or Interstate battery dealer. You will need 2 U1 sealed AGM or Gel cell batteries and the cost will be $175.00 to $218.00 for 2 batteries. After installing the new batteries be sure to charge before use and then charge every nite for the next 20 days. If you use the chair daily charge overnite If you don't use it daily always store fully charged and charge at least once a week Hope this helps you

John usually the cause is that the batteries are getting weaker and need to be checked and replaced if needed The batteries will last about 2-3 years if charged correctly. But you can develop a battery that has become weaker and this affects the other battery as well. So you have to replace both batteries I have seen new batteries last only 3-6 months because of a bad battery New doesn't neccessarily good A tech should perform a load test on your batteries to determine if they need replacing Hope this helps you

YY count the number of flashes ie 4 flashes pause 4 flashes pause. This will give you the error code and will tell what is wrong with your chair Check out my tip on Flash codes if you can't find them in your manual. Without fixing the problem that generated the flashing you won't be able to use the chair until the problem is fixed. If you want you could contact the provider that sold you the chair and have them troubleshoot the problem for you Hope this helps

Bob why don't you run a small 2 wire cable from one battery to the armrest where your joystick is located and attach the new horn and a small push button switch to the joystick bracket coming from under the armrest. loosen the knob tightening the joystick bar and pull it out enough for you to attach the horn and button to it. I 'm not sure if that will work because I don't know what the new horn looks like but you can also mount the horn under the shroud near the battery and run the wire to the switch at the joystick. Good luck sounds like an good project

Do you mean the freewheel levers?
The chair will not drive if you have it in freewheel. Push the levers back in, and then turn the chair off and on. It should be working now.

The green light won't come on until the batteries are fully charged now if after an overnight charge you still don't have a green light then I would replace the batteries. Hope this helps you

the seat post is probably rusted in the post. Try lifting the handle and twisting the seat and pulling up at the same time it can really be very hard but keep trying and maybe get some help to lift as it is being turned. I've had to use a hoist to lift it off the floor and twist the seat until it comes out. Hope this helps