Top 20 Select Jazzy Used Electric Wheelchair Questions & Answers

James, the flash code for some of the Jazzy's say that your brake solenoid wiring has a problem, check your connections to both sides of the chair. Strege Mobility I’m happy to assist further over the phone at https://www.6ya.com/expert/bill_bcbb89783b08c489

This charger is suspect I would take it to your local battery outlet and have them check it. I would not trust this charger! Strege Mobility I’m happy to assist further over the phone at https://www.6ya.com/expert/bill_bcbb89783b08c489

the code that is given by the Joystick is indicating where to look for your problem , once the the correct repair is completed the code should disappear. I’m happy to assist further over the phone at https://www.6ya.com/expert/bill_bcbb89783b08c489

You may have a faulty speed control depending on the model. There are hand held programmers that are used to adjust the speed and other parameters. Your local dealer or mobile technician should be able to make that adjustment for you.

Black onto the negative post and Red onto the positive post, one cable per battery,two sets of cables. do not cross cables on to more than one battery. Strege Mobility I’m happy to assist further over the phone at https://www.6ya.com/expert/bill_bcbb89783b08c489

I tell my customers to charge the chair with the joystick on! otherwise it should be upright in a drive position do not charge a chair upside down! I don't know why someone would do that but... once the charger is plugged in the chair is inhibited from driving, so if it is plugged in it won't drive. Strege Mobility I’m happy to assist further over the phone at https://www.6ya.com/expert/bill_bcbb89783b08c489

this is a problem with the Joystick or a connection to the joystick. Check the wiring first. It has been my experience that the controller may also have a hand in this code. Have a Qualified tech check it out. Strege Mobility I’m happy to assist further over the phone at https://www.6ya.com/expert/bill_bcbb89783b08c489

You may have a thermal rollback issue. Try charging the chair overnight and leave the controller on while charging. This will give the control module/joystick time to reset themselves. Thermal rollback happens when a certain temperature in the motors is reached. The system shuts itself down to protect from damage.

7 Flashes indicates a joystick trip. Turn off your chair, ensure the joystick is in center position without anything touching it and turn on chair. This should clear the 7 flash code. This problem is quite common amongst power chair users. It typically occurs when something is pressing against the joystick as you are turning the chair on.

it maybe a controller fault to know for sure have a tech with a programmer check it before blowing a lot of cash on this chair! Strege Mobility I’m happy to assist further over the phone at https://www.6ya.com/expert/bill_bcbb89783b08c489

There are about 30 models of Jazzy. Which one do you have?

With a new charger and new batteries there can only be one other problem assuming all the wiring is connected properly. There is a 7.5 Amp in-line fuse hidden in a fuse holder off the charging harness. This fuse may have blown. I usually check this fuse first since it is usually the culprit and most difficult item to locate under the back cover. In rare cases the ammeter burns open and will cause the unit not to charge. After checking the fuse you can jumper one or both these items to see if it will charge and then purchase new parts. Hope this helps.

Make sure that you are not in freewheel. If you can push the chair and the chairs rolls easily you are in freewheel, look for the freewheel levers and place them in the drive mode. If you are not in freewheel then you could be in sleep mode If you have a manual see if it tells you how to get out of sleep mode. If not within 10 seconds of turning the chair on try pressing the horn button twice and then turn off then back on to see if you stopped the blinking lights. I don't know with the older joysticks how else to get it out of sleep mode. If you are still having problems you can call Pride
Mobility @ 1-800-800-8586 on Monday ask for Jazzy Tech support and they should be able to help

Hope this helps you

You have a serious problem. When something gets wet and it has power to it then the power tends to corrode things. The control board has contacts inside it that are subject to being corroded and also the switches could have been damaged too. Unfortunately the controller is really expensive. http://www.monsterscooterparts.com/jazzy1120.html

hello,if you visit the people who built the wheelchair,Shoprider for example is where i went for 1 solution & there i was able to download a PDF File of the troubleshooter,you should also be able to print it off for your future records,there was so many solutions there,pics of the joystick with different lights lit up and a solution beside each 1.i am disabled myself,i hope i have been of good help Colin.

Instruction Manual:www.FixYa.com/Insrtuction+Manuals & for extra info type in a brouser: local dealer for your product giving its name & it maybe a seperate box for you to enter your Post Code,enabling easier searching for you.

Engage the motors on both sides with the lever under and near the motor!

It could be that the acceleration is set to low. This setting adjusts the time it takes for the chair to reach maximum speed that you have selected on the joystick. With a low setting, it takes it a few seconds to get to maximum. Reprogramming the acceleration to a higher setting decreases the amount of time for the chair to hit max speed. You will need a PP1 handheld programmer from P&G drives technology to change the settings, or take it to a local DME specialist who will usually have a programmer to reset the joystick.

Here's a link to the owners manual that has the codes listed in the troubleshooting pages.
http://www.pridemobility.com/pdf/Owners_Manuals/US_Jazzy/US_Select_Series_om.pdf

Hi

Rapid flash of lights indicates a fault in the VSI or the electrical system. You need to refer to " VSI Error Codes" on page#32 of this User Manual:

Pride 1143 Jazzy Electric wheel chair User Manual

Please do accept the solution if the issue is resolved or else revert for further assistance.

Thanks
Rylee