American Standard Colony 2388.012.222 Linen Two-Piece Round Front Toilet - Page 9 - Answered Questions & Fixed issues

you need to go back in and check your work it seems that it has been installed in a lower setting look at the directions, most shower assembly's have energy settings.usually just have to move the stopper to the farthest point to the left (counter clock wise).good luck.

turn the drain counter clockwise it will increase the space between the tub and the rubber gasket on drain cap

Inline heaters for whirlpool bathtubs will not and cannot maintain any comfortable water temperature. Their sole function is to slow the time it takes for the water to cool off. The myth of their capabilities has long been a misleading sales propaganda joke in the industry.

Not all manufacturers put their model numbers on their tubs. Those that do will almost always post it on a label in the area of the tub where the back usually rests in the region of the motor but not on the motor itself.

I believe your quarter size cap is an air control for you jet. It controls the amount of air coming out the jet when the tub is full of water and the motor is on. You should see the difference in swirling water turning it from right to left or the other way around. If yours has a leak then I certainly hope you find the Model number. Good luck.

adjust the chain that connects the flap to the handle give it some slack but not so much as to get chain laying under the flap good luck and hope it helps

you need to use a screw driver.

replace the fluid master

you must pull the toilet up and try to retreave what ever is cought in the trap.

Hi, you can get the whirlpool jacuzzi related parts from Jacuzzi on 1-800-288-4002.

Serval reasons: (1) noise from handle chain being metal-consider switching to lighter plastic type. (2) The rubber flap which lifts up when handle is pushed down and seals "when handle is let go" to allow water to fill in take maybe worn to the point of needing replacement-Go to any Lowe's/HomeDepot and they will walk you through replacement process of just removing old one and putting ends in place over hooks to install new one. Takes me 1 minute to do. (3) Adjust the water cut-off valve that supplies water to tank so it can feel up rapidly by just turning the value. If value is hard to turn try using some oil or WD-40 on it. Remember that one way opens to allow quicker fill up and better flush and other way just turns water to toilet off. If now of these things work then just give me a yell and I can advise further.

You can connect to the main stack coming from the main floor. You must however install a vent to connect about 42" up inside the wall.

Check the fill level, if not enough in the tank, you can have what you describe.

79 1/2 inches...Hope this helps.

I hope you get this... it's posted in the bath section!

An easy answer... Download the drivers here:

http://broadband.motorola.com/consumers/support/default.asp?supportSection=DiscontinuedProducts

you must tie into the main stack or make a new one and run it through the roof.

YES!!!! all a window does is change the vapor into liquid. What is needed is to get the moisture OUT OF THE building. I prefer Neutone 200 CFM unit, for get specs, they are all way too low. You are combating health issues if you allow moisture to remain....mold...

Also, the exhaust ducting needs to run downhill as it exits the building, or you risk moisture dripping from the fan...

Futher, put a 60 minute timer on the fan, and run 45 minutes (at least) for every shower....

Hi,
No that is kinda normal for some toilets and I would not worry about it...

heatman101

You can get the progremme fron google search Engine

probably hair stuck in the drain. did you remove the stopper "pop up" if no hair or blockage there or in the trap, then its further down, you will need a small snake. 1/4 inch cable works well in bath and kitchen drains.
you can purchase one at home depot.

you can get universal replacement parts from your local hardware or plumbing supply store. For some models you may have to remove the tank from the bowl. Most you can unscrew from inside the tank without removing. Good luck.

If it is truly a porcelin top then you can use a product called plumbers putty available at your local hardware store. It will conform to the shape of the drain and provide a good seal. If this is a cast marble or resin type of product then plumbers putty will void any warranty and possibly discolor the sink. Ensure it is indeed porcelin before continuing and follow the manufacturers directions for installation. Good luck with your project.