20 Most Recent Kohler Model 7193: Drain For Sok® Overflowing Bath - Vibrant Brushed Nick - Page 6 Questions & Answers

run the 'setup.exe' of your game, and follow instructions on the installation wizard.

need to turn it not the handle..the part just under it

Hi,

The part you need is the 500520 pressure balancing unit shown here

The part can be replace from the front with out removing the valve body....

You will need to find a Kohler parts dealer in your are to get the part or order it from someone on the internet...installing it should not be that hard....you can DIY....
this will fix your problem...

heatman101

If the faucet was working before and then just stopped, it is the mixing valve or a clogged supply line.
turn the water off and remove the mixing valve. Turn the water on and see if you have good flow from both hot and cold ports inside the faucet.
Caution- this procedure can get messy, close the shower curtain or door.
Call Kohler and ask for a new mixing valve for free.

Place a few drops of vinegar into the screw hole and wait a little bit. Try removing the handle again, sounds like it is just stuck on the cartridge stem. The handle should come off first, and then the bonnet. Here's the parts breakdown for your faucet from Kohler.

Hi,
There is a loose washer in the faucet...this flaps as the water goes through it and makes the vibration...
You either need to replace the faucet or the cartridge (washer) in the faucet that valves the water...
This will stop that vibration and hammering sound

heatman101

all of kohlers baskets fit their sinks, even older model sinks.

do you have a special strainer, or sink?

have you contacted Kohler direct? or one of their distributors. a wholesale plumbing supply house (NOT lowes or home depot) in your area will be able to help you also

is this what your looking for??
http://www.alibaba.com/product-gs/216898427/Sink_basket.html

Kohler makes their sinks standard, and most all sinks are the same size hole, yes it will fit.

hi, if you push down on the button and giggle it around it should pop back up once you have it up remove it by unscrewing it and clean the area so that it won't get jammed again

always replace cast iron if its not a problem to do so, especially if it looks rough or is leaking or rusting. there are simple special black neoprene boots used to connect cast iron to pvc and do not require anything but a screwdriver, no slovents or sealers are required. always check for leaks if you make an underground connection before you cement the spot back up. its better to use gravel to fill this area in if your particular situation will allow.

Aerator ,sounds like it is not on right ,maybe cross threaded,or just not tight

NOT A EASY FIX,THE CABLE IS NOT ADJUSTED RIGHT,

Hello. You will most likely have to get a model specific rebuild kit from kohler, or home depot and replace the O rings. Joe

I would definitely try adding washers from under the sink. Has it been caulked? Caulking will help to fasten the faucet to the counter.

Try a Blanco Strainer. They come in many assorted strainwers. Ive been selling them for years and not one has come back for return

Spring loaded chrome stopper will not stay down to fill tub with water.

My husband is a plumber. He said to check for pinholes. U should be able to see them. If u find pinholes u can email us and he will tell u how to proceed from there. Email- [email protected]

Okay, remove 2 phillips head screws at lever handle/overflow.

Pull firmly with much effort and bowing the connecting rod a bit.

Up will come a heavy duty spring on the end of the rod.(prolly a big slimly hair ball too!)

Hope you get the spring, cause that's what works the drain stop.

If spring doesn't come out you'll have to "fish" it out.

Clean everything up real good and flush drain good also now.

The "Secret" now is to put the Lever,rod and spring assembly back in and replace screws and get the lever flipped to the left BEFORE you put the Drain Stop in.

How does it open and close do you press it down to close and press again to open?