20 Most Recent
Homelite Mighty Lite Lawn Trimmer - Page 9 Questions & Answers
My starter pulley for my "homelite mighty lite
This is a labor intensive procedure to just get to the recoil/starter unit so it can be inspected for the problem. Here is how you get there.
Remove the tube that holds the flex-drive shaft from the front of the motor cover.Remove the rear engine cover. Remove the throttle cable from the carburetor. Mark and unplug any wires for the on/off switch that go to the ignition coil (underneath front cover) if possible. Now if you have pulled the driveshaft tube out of the way, the clutch drum is up next. Inside it, screwed into the very end of the engine's crankshaft is a Torx #20 screw. Before you loosen it, you will have to lock up the engine. To do so, remove the spark plug. Pull on the starter until the piston is down, then insert a length of clean, soft rope into the engine. The engine will come up and compress the rope, thus locking it in place to allow clutch drum and clutch removal. Loosen the T-20 (Star bit or Torx head) screw inside the drum.. You may be able to remove it with a long thin-blade screwdriver also.It probably won't come completely out...it is made this way. Next, remove the clutch. It is screwed onto a small threaded section of the crankshaft Removal is counterclockwise.. It will be pretty tight. To help, apply peneterating oil. Whack the ears of the clutch near the center with a hammer and a dull flat-blade chisel or a small piece of wood unless there are bolts. then use a wrench. It will turn counterclockwise for removal and there will probably be a removal direction arrow on it's face. After getting that off, remove the Torx screws holding the cover to the engine. The starter unit should be mounted inside as it mates with the top of the flywheel to start the motor. Remember to preload tension (5-7 turns) on the starter unit. Make sure the handle is installed. Jam the unit with a screwdriver or vise grips so you can insert and tie off the new rope. Then remove jam device and let recoil pull your new rope into place while holding the handle. Reassemble and you are done. Disassembly requires Torx head drivers and a good flat-blade screwdriver. Post back if needed. Input your model number here to find a pulley. I will give you a couple of places to check. http://www.ereplacementparts.com/homelite-trimmer-parts-c-18807_20299.html http://www.outdoordistributors.com/Homelite/Homelite_Main.html
I have a Homelite HLT26CDNB
After near-divorce over our Homelite Fiasco 2000, we discovered that the line holds out if you only run it at about 60% throttle.
What kind of gas does a homelite 26ss use
First of all, thank you very much for choosing FIXYA today for your technical support needs.
Here is a direct link to the ONLINE USER'S MANUAL for that model:
http://www.homelite.com/system/manuals/stringtrimmers/UT32600_UT32650_056_trilingual.pdf
To view the Owner's Manual with Operating Instructions just use your mouse to click on the link, which is the underlined and blue highlighted text just above.
This will open a new web browser page automatically for you and allow you to view the information at the website indicated and the contents of the Owner's Manual.
You may need ADOBE READER installed on your computer to read PDF documents, although many computers already have this type of utility pre-installed.
You can download this free at
WWW.ADOBE.COM if necessary.
Click on the DOWNLOAD ADOBE READER button on right side of the ADOBE home page when you get there, then follow the onscreen instructions to install the software on your computer.
Your product has a 2 cycle engine and requires premixing gasoline with Homelite 2 cycle oil. The mixture needs to be at a precise 50:1 ratio.See page 7 of the manual for complete fuel mixing instructions and illustrations.I truly hope that was helpful to you.
Good luck and take care.
Joe.
I have a mighty lite
You can get a rebuild kit from
PartsBuggy.com. Just go to their
cross-referencing page and enter the model # from your carburetor (it should be stamped into the body of the carburetor), NOT the trimmer model #, and you'll be given all the available kits for it.
How do i remove the primer bulb on my homelite
The primer bulb should be attached directly to the carburetor. There will be a plate with 4 screws, once on each corner, which you will have to remove to get the primer bulb off of the carburetor. You can find replacement primer bulbs at
PartsBuggy.com.
Hi I need a priming bulb now I know where it goes
There are 2 types: on top of carb type, and, remote with 2 nipples type. Both are really inexpensive. Many online vendors like partstree.com, outdoor distributors etc. have them. You will pay MORE for the 7.95 shipping charge than the bulb costs. I use Ebay to find many parts at low, low prices and many sellers ship FREE. IF you don't go to a small engine shop for your parts, then Ebay is your next best bet. If you order online, minimum shipping charges will kill you.Become a member of Ebay ....you will be very glad you did!
Not finding what you are looking for?