20 Most Recent Homelite Consumer Products 4.0 Amp, 13 In. Trimmer - Page 7 Questions & Answers

You don't need to own a mint plantation or freeze your mint. You can have it at home and without much effort. How? With AeroGarden pods for veggies, herbs, flowers and plant-based foods. AeroGarden

Perhaps you can follow these simple steps to solve your problem:

Start and let the saw run until its run out due to empty gas. Take off the cylinder cover, which sits on top of the saw. Using the needle nose pliers grab the rear end of the fuel line and gently pull it off the carburetor.

Remove the gas filler cap from the tank. Use the needle nose pliers to grab the fuel filter in the bottom of the tank. Pull out the fuel filter and the entire fuel line from the saw. Use the pliers to pinch the fuel line and with your hand pull the fuel filter off the fuel line. Throw both of these away.

Cut off about 10 inches of new fuel line and insert the metal wire into the fuel line. Push the wire and fuel line into the gas tank and through the hole at the bottom until you see the line come out near the carburetor. Don't connect it to the carburetor yet.

Pull the metal wire out of the line and cut off any excess line with the scissors. Pull it back out of the tank slightly and insert the fuel filter into the fuel line. Push them back into the tank.Use the needle nose pliers to grab the rear end of the fuel line and attach it to the carburetor.

I hope these helps. ??

Unlikely as it has a 4 stroke engine. Unless you didn't bother to check the engine sump oil. Basic maintenance here. Try and turn the crankshaft output with a wrench. https://www.google.com/search?q=Homelite+pressure+washer ..

Read the 2stroke oil can

A 50-1 ratio is the answer.

check filter or carb needs cleaning -rebuild or replacement

Chainsaw oil pumps are fairly simple affairs, to increase oil flow you obviously cannot increase the engine speed, so you increase the throw of the pump shaft, so the pump shaft not only rotates, it moves back and forth ( the throw ) so the back of the pump shaft is cut off at an angle, the adjuster screw sits on the back of the shaft, so now when it rotates it moves in and out due to this angle, so the close the screw is to the centre of the shaft the lesser the throw, the further out the bigger the throw, so unscrewing the adjuster ( anti clockwise ) increases the flow, and visa versa.

Standard plug gap for a chainsaw 0.5mm

Check the fuel lines, it has small leaks

Here is a link to a search showing the manual as a pdf. https://www.google.com/search?sxsrf=ACYBGNTfb-N20gTi_jyY8AhRQsrREyx1gQ:1569087551920&q=homelite+bx90+bandit+blower+manual&spell=1&sa=X&ved=0ahUKEwirhJ3RuuLkAhUBXq0KHR1uCvMQBQgvKAA&biw=1242&bih=598

Go right to the source - Homelite: http://manuals.homelite.com/

Try cleaning the carburetor and blow or clean jets. Then new mix and clean fuel. Start up, and probably set the idling to a little faster to start then adjust for good idle speed so it won't stall. Hope this may help.

What we normally say is good quality two stroke oil 50-1, two stroke oil from unknown manufacturers 25-1

The oil ratio is not adjusted to the engine it is the formulation of the oil. You mix your oil the way the bottle states. I have been working on 2 cycle engines since the 70's at a motorcycle, ATV and lawn & garden dealership. If you have doubts about a 50:1 oil do like I do and put 8/10ths of a gallon of gas in you jug and use a bottle of oil for a gallon and mix.

As with any brushed electric motor both brushes should be changed, it is not good practice to have different lengths of brushes.

Defective carburetor.

How to Remove the Cap to Replace the Line of Homelite Trimmer Homelite UT33600 Operator Manual General Maintenance Advancing Line...