20 Most Recent Pride New Mobility Victory XL 4 Wheel Scooter - Page 5 Questions & Answers

Do you get any flashes from the controller lights? This is usually the way you diagnose errors. A high number of flashes/beeps often means there is an issue with the controller or joystick. Batteries are only fitted if they are needed so a 'spare' battery isn't very likely. Most wheel chairs and scooters need a powerful battery to spin the electric motor so a pair of batteries are used. The two batteries also act as a counter weight to keep the chair upright. They are normally fitted in a 'serial' or 'in-line' set up. Basically into one battery, across to the second battery then out through the second battery.

If you use Lithium cells, you must use a special charger and have a protection circuit for the batteries otherwise you will have a fire and no ne can put out a lithium ion battery when burning.

hi, hope this helps. regards rob

The rubbing sound you are describing could be caused by a variety of issues, such as a problem with the drive wheel or the motor. It could also be caused by debris or an obstruction getting caught in the moving parts. It is best to have the chair inspected by a qualified technician to determine the specific cause of the noise and to make any necessary repairs.

https://www.pridemobility.com/pdf/owners_manuals/us_scooter/us_zt10_om.pdf (Page #12)

I have Raptor mobility scooter service manual. Let me know if you are still interested in it, I can send you PDF copy.

Not there isn't. It is a combined motor, brake and gearbox. Don't just buy a new one, find out what is wrong with the old one. https://www.monsterscooterparts.com/mobility/mobility-brands/gotrmo/goeltrs/motor-brake-and-transaxle-assembly-for-the-go-go-elite-traveller-sc40e-sc44e-and-ultra-x-sc40x-sc44x.html https://www.google.com/search?q=gogo+elite+traveler+sc40e+won%27t+move ..

The full voltage across the Pride Go Go 3 Wheel Throttle pot should be 12 volts.

Question edited for clarity. Question moved from Computers. Beep codes. Looks like a throttle issue. https://www.google.com/search?q=7+flashes+and+beeps+on+a+Rio+4

A 3 then 4 flash sequence is showing the Freewheel Lever is in the freewheel position and the scooter cannot power the wheels. Turn off the scooter move the lever firmly in both direction 2 or 3 times then leave in the 'Drive' position. Turn the key back to the On position and check to see if the flashes have stopped. As Scooters age these switches can wear out and fail and all you can do is replace the switch assembly as they are often a 'Non Repairable' part.

Sounds like old exhausted batteries to me.

Joystick issue it says here. Check the connections. https://www.manualslib.com/manual/134614/Pride-Mobility-Infmanu1773.html?page=16 ..

Speed is normally programmed into the control board software. The top speed is set for stability especially in cornering. You use them for mobility issues, so image being on the ground with it partially on top of you because it tipped over! https://www.google.com/search?q=+pride+go+go+sport+Speed+limiter

Did you reset the breaker?

Troubleshooting ' Pride Mobility Scooters

https://getaroundmobility.com > troubleshooting-pride-... Aug 21, 2020 - The second option for resetting the scooter is to put it in "freewheel mode" by pushing forward the manual freewheel lever at the back of the ...

Victory XL Manual (UK).p65 - Pride Mobility

https://www.pridemobility.com > pdf > intl_scooter PDF When your Victory XL's main circuit breaker trips, the reset button pops out and your Victory XL shuts down. (The main circuit breaker reset button is mounted ...

• The Ultimate In Style & Performance® - Pride Mobility

  https://www.pridemobility.com > us_victory_xl_om PDF rear section of your Victory XL, near the manual freewheel lever and the main circuit breaker reset button. See figure 7. Batteries. The batteries store the ... ..

Question edited for clarity. It sounds like you have a connections issue somewhere, or the display / control board has a fault.

Question edited for clarity. Page 19 of the manual shows the main circuit breaker. https://www.pridemobility.com/pdf/owners_manuals/us_jazzy/us_jazzy_614_series_om.pdf

basic troubleshooting instructions: jazzy 614/jazzy 614hd

https://www.pridemobility.com > pdf > infinfb246... PDF ? Make sure the main circuit breaker has not tripped-push in the main circuit breaker reset button. ? Make sure the controller is completely connected to the ... ....

If you are in the UK; https://www.ebay.co.uk/itm/333805380844?hash=item4db859e4ec:g:bVsAAOSwP9lfj9a7&amdata=enc%3AAQAHAAAA8OgRVYhLYiafPNv04YQ0ZCivnH5AkcMfB%2BHBkvtlh4ATRytcci6KGQL5SfE9MLUsEXTaCt968Toz407vLs6NP2kFsLf1Iju0qlx5IvnyTNYGfobnxebAJPm8jtbVlOd4pWNmkwquvjIOZQZPnvzv9GdQWUsQaWIFpCtAeqlSxfDiA28TrnAUU9M%2Fk9zwxsARFZAqZA68clVaCO7JkdYKp4pSLJMTRzeOrfr1f7Fv7u1kFF8yGs6SME7ZzHup4JNY8ESpT5oiyNQc7ib6ijbZJASgDJuMnKNKsg9qs%2Fj5kEPg74iUWfC8zjzNBa5GI8iofw%3D%3D%7Ctkp%3ABFBMsI349sNgorhttps://www.ebay.co.uk/sch/i.html?_from=R40&_trksid=p2553889.m570.l1311&_nkw=24v+8amp+mobility+scooter+charger&_sacat=0

This is about as good as it gets. Very simple wiring. https://wheelchair-parts.com/replacement-parts/pride-mobility/r3-1700-raptor-3-wheel/charger/charger-assembly-8-amp-off-board-cte-us

I would check/replace the motor brushes.

Possibly the control requires replacing under the paddle.