Pride Used Mobility Jet 3 Power Wheel Chair - Answered Questions & Fixed issues

Is it in freewheel mode?

Check your freewheel levers are in drive mode. I’m happy to assist further over the phone at https://www.6ya.com/expert/bill_bcbb89783b08c489

The quick disconnect normally has a tab that when pushed will allow the connectors to come apart. You will have to look. The connectors normally are white nylon, but they could be any color. It should be there if the manual is correct for your chair. Best I can do without seeing a picture or the chair itself.

The joystick needs to be reprogrammed.

from the manufacturer's web site.

You can get that information from Pride's web site. Download the service manual.

Pride Mobility has the service manual on their web site. You can download it.

Sounds like a battery issue. Also with the speed indicator is it blinking or ripples from side to side?

Remove the seat, cover

Are the leds flashing all at once or scrolling from left to right?

It is typically the cable leading from the joystick to the control unit. Disconnect it and reconnect it. Check the cable for any cuts or pinches that could cause a short. There are a number of issues that creates the 9 flashes. The code just means there is a disconnect somewhere. If you can take the chair to a DME company who can place a programmer on it to read the fault codes, it could help locate the issue.

Hi sounds like a gearbox issue, could be dry but then ask the question why every five feet, think of the gears and the amount of movement required, could be a tooth missing or damaged, is it possible to get the wheelchair on it's side to find out what motor is clicking ? Please NOTE: take care here.... i don't suggest for one minute you do this alone, and powering the scooter while on it's side must be done with care.... just jack one side up somehow and power the chair then do the other side .... once again taking extreme care when carrying this out... you will need help... Regards Rob www.gewizrepairs.co.uk

What do you mean Locks up? When you take it out of the machine does it sping free?

Have you ever solved the problem? My Jet 3 does the same thing and i would like to know whats causing it. Thanks Rangr90

Hi I a Phillip the "DFW Mobility Specialist"send me a email at [email protected] with the serial # and can get you a price and order you the part.

The batteries need charging and when you plug in the charger and the power is on the lights wil flash indicating that the charger is plugged in. Now look at the rear of the chair near where the charger cord plugs into the chair and you should see a voltmeter. With the charger plugged in the voltmeter will indicate about 5-6 amps and after charging overnight the voltmeter should be reading 0 amps. If when you plug in the charger cord and the voltmeter indicates 0 amps then I would suspect that the charger is not working or that the fuse is blown in the charger circuit. The only way to see if the batteries charge would be to borrow or find an offboard charger that will plug into the charger port located under the front of the joystick and after charging for 10-12 hours see if the battery level lights show full charge Hope this helps

check the motor brushes if they are 1/4 inch or less replace them. Next, after driving the chair for a while check the motor casing near the brake assemblies on the rear of each motor if the casing is hot then you have a sticking brake pad or pads and this can cause the excess battery drain. If you have sticking brake or brakes unfortunately the whole motor assembly will have to be changed Hope this helps

the batteries are not charged and need to be replaced. The reason you have lights is because the charger is supplying power to the chair and the chair will not move when the charger is plugged in because of the inhibit function. Replace the batteries and make sure you charge before use Hope this helps

Please visit-www.alldatasheet.com i have a scooter myself,glad to have helped.The site is free Colin.

Please visit :-www.alldatasheet.com its free and you can download your needs as PDF Files via your Adobe Reader,i have 2 scooters myself,and i know what its like to be stranded,im glad to have hopefully helped you Colin.