Top 20 Stanley Professional Backpack Poly 4-Gallon Sprayer #61804 - Page 6 Questions & Answers

I would contact the manufacturer and find out if they will fix it for you. https://psiproducts.com/product/landa-surefire-burners/

Question edited for spelling 'ryody'? It is written in yellow all over it! https://www.google.com/search?q=Ryobi+grass+scorpion+fuel+lines ..

To inspect fuel lines on a Baumr-AG CSX75 demolition saw, locate the lines, check for damage, and replace any damaged lines to ensure proper fuel flow and safety.

This may help: How to Clear Codes On A John Deere Skid Steer ' Pap? Machinery (papemachinery.com) John Deere 310SL Backhoe Loader Diagnostic & Test Service Manual (TM13297X19) ' A++ Repair Manual Store (aplusmanual.com)

Typical carburetor low speed circuit is blocked but can be fuel or other. Likely needs carb adjust, clean and/or rebuild.

Question edited for clarity. Yes some parts are available, mainly seals and tips. https://www.google.com/search?q=Mintcraft+532+7713++sprayer+parts ..

There are no parts listed for it. If you add the works 'parts' to this query it quickly disappears to Pond Pumps. You would have to remove the pump from it and search by the numbers that will be printed or embossed on it. Google will find it, or search Amazon direct.

1. Place the Pergola structure onto a flat surface in an area with adequate space for assembly and use. 2. Unwrap the hardware bag (included with the pergola) and place the contents on the flat surface near the structure. 3. Begin the assembly by attaching one of the long side rails to the top of the Pergola. Insert the rail into the slot at the top of the structure. Securing it with the provided hardware. Tighten the four screws using a drill to firmly secure the rail in place. 4. Next attach the second long side rail in the same fashion. 5. With both side rails firmly in place, attach the short side rails. Insert the rail into the slot at the top of the structure and then secure it with the provided hardware. Tighten the screws using a drill to firmly secure the rail in place. 6. Repeat this same process to attach the remaining short side rail. 7. Attach the four corner brackets using the provided lag bolts and washers. Some models may require different hardware for this step. 8. Secure the corner brackets with the provided bolts and washers. 9. Attach the remaining lag bolts into the holes in the top of the Pergola frame. 10. Tighten all the screws and bolts using a drill which will secure the frame in place. 11. Place the canopy (sold separately) on the top of the Pergola frame and secure it using the provided hardware and tools. 12. Once the canopy is secured in place.

The solenoid should have three posts. Two large contactor lugs and a smaller terminal for control (batt pos). The solenoid frame must be securely attached to the mower chassis as it is the control winding return path (batt neg).

The large gauge red wire from the positive battery post and 2 smaller red wires stack on to one contactor lug (post 1). The other large gauge red wire from the starter goes to the other contactor lug (post 2). The small yellow wire goes to the smaller solenoid control terminal (center post) and energizes the relay with battery positive from the ignition switch S (start) terminal.

Refer to attachment, wiring diagram.

look up your model for the manual ------- https://www.mountfieldlawnmowers.co.uk/support

Generic parts made in China. https://www.google.com/search?q=Replacement+swivel+base+for+Wilson+Fisher+Glider+Chair ..

https://www.google.com/url?sa=t&rct=j&q=&esrc=s&source=web&cd=&cad=rja&uact=8&ved=2ahUKEwjF7pm4xpSCAxVEmIkEHaPbAvoQFnoECB0QAQ&url=https%3A%2F%2Fwww.orangetractortalks.com%2Fforums%2Fthreads%2Fcan-i-determine-what-model-year-from-serial-code.45724%2F&usg=AOvVaw320X8niJs2M0dRBU5lxjT6&opi=89978449

Leave fuel cap off and filter submerged. Ether fish out the fuel return or at least position where it's visible. Then press the purge bulb several times. Fuel should spurt out the return. If no fuel from return line and air bubbles come from filter, lines are reversed somewhere.

It looks like it is part 64? https://www.partswarehouse.com/Worx-WG303-16-Inch-3-5-Hp-14-5-Amp-Electric-Chain-Saw-s/326235.htm https://www.google.com/search?q=Worx+Electric+WG+303.1+chainsaw+parts ..

Likely insufficient battery voltage. Test battery and charging system.

On early model carburetor there is a throttle stop adjustment screw, newer models require mechanical adjustment. Observe the throttle butterfly lever when adjusting the throttle.

https://youtu.be/DZrcO6I_86U?si=8UxSziZ2h5u7-X4F

Time stamp 55 seconds.

Question edited for clarity. Question moved from Computers to Hedge Trimmers. Unfortunately not for that model, just a parts diagram. There is a manual for the HG 50. https://www.google.com/search?q=Electrolux+HG18+manual .. ..

Disassemble the plastic part of the head where the line feeds from. There are normally two plastic clips. Remove the line and refeed it.