20 Most Recent Troy-Bilt® Briggs and Stratton Chipper - Page 2 Questions & Answers

I need a gas tank for a 020245 Troy- bilt pressure washer 2200.

parts are NLA Murray has gone bankrupt, assumed by Briggs & Stratton. Many Murray parts are NLA I’m happy to assist further over the phone at https://www.6ya.com/expert/rolandw_c013176d62ee17ae

You should be able to get the chipper's model number off the tag or label. With that model number you can go to the local small engine repair and parts shop to get the replacement pulley or you can look online at Troybilt and using the model number look up the drawings for the chipper and select the correct part and order it from them. Partstree.com and outdoordistribut

Get the model and type number off the engine and you can go to a website like partstree.com or others and with the brand and the model and type number you can get diagrams of the engine.

I hope this is helpful for you.

how do i chanebelt on super tomahawk chipper

Like a car engine, there should be a tensioner pully. If not, each pulley should have a bolt that hold it in. To remove the belt, unbolt one pulley, (whichever is easiest to get to, or more feasible to remove) - When installing the new belt, put the pulley on first, and if need be, use a screw driver to "pry" the belt over the pulley into place. This will not hurt the belt.
There should be however a tensioner pulley, or one of the pull belt pulleys should have a slider bracket. Make sure first if this is true.
Please let me know if you need further assistance.
carsandcomps,
Guru, Premium Expert, Phone Support, Live Chat @ Fixya.com

carb is plugged up, take off and buy a can of carb cleaner and take apart, (easy) and clean

Any MTD dealer can get you these parts. Or go to MTDparts.com to order them. If you need further help, I’m available over the phone at https://www.6ya.com/expert/matt_8dbc24bf722649ac

This is serious. Don't use the mower till it is fixed. Probably the carburetor has malfuntioned and may need to be removed, disassembled and possibly rebuilt. Major flooding is ocurring somehow either by the carb or a mechanical failure of the engine.

Hi,
Most small engines have a cap where you check your oil level. This is also the access for putting in oil.

Here is a link to the Troy-Bilt site for chiper shredders. I don't know what model you have but you can select your model and obtain a users manual.

http://www.troybilt.com/webapp/wcs/stores/servlet/category2_10001_14102_54996_54995_54995_-1#

I hope this helps you. Good luck!

Your piston is worn and galled, you might be able to do a rebuild with a new piston and rings and hone the cylinder, but please always consider cost, of the price of a new engine,if you cannot do the work yourself,

Get a can of carb. cleaner and squirt some into the air intake as it is running. Let it run on this carb. cleaner for a couple of minutes and you will clear your clog. J.

use pbblaster to free it. it is stuck due to varnish

pull plug and try to pull start if moves than it was vapor locked clean plug and try to start if no movement with plug out than internal engine or pull cord jammed

if the starter rope fails to retract, then you need to either fix a broken spring, or put a new one in. You'll have to take the engine cover off, and you'll be able to see how to take apart the retractor assembly. Often times, just the end of the spring will break off, and if you have a grinder, you can grind the correct shape in it again, and reinstall it as is.

Hi,

Here: http://www.brentchalmers.com/

Keep all of those fingers out of the shredder!

Hope this helps, if so pls leave feedback, if not let me know!

Ok, if the gas has been sitting in the fuel system for two years, it is now no good and has "varnished" the carb etc. The fuel system must be drained and run dry at the end of every season or you will have this occur. The solution is to disasemble the carb and clean it with carb cleaner and reassemble. You will need a few new parts and seals to do this and a lot of patience. Easy way is to take it to the service guy and live and learn.
To prevent this, use a fuel stabilizer in the fuel before storage.

you can try a MTD ride on mower dealer or steelfort Engenering web site or mtd web site.

Straight 30w NOT 10w-30

prefer air-cooled engine oil from mower dealers or some auto supply stores have air cooled engine oil. I’m happy to assist further over the phone at https://www.6ya.com/expert/rolandw_c013176d62ee17ae

If this is a 2 stroke,remove the fuel filter and check,or replace,and check all the small fuel lines,if this is not a 2 stroke,check the pick up tube in the fuel tank,to see if it is blocked,if it is not,then remove the fuel tank,witch you will have to do to check the pick up tube,and clean the carb.Make sure all the holes in the carb.are clear.