Jump Start 4' Fluorescent Plant Grow Light System - Page 5 - Answered Questions & Fixed issues
BR 600 blower fuel line pops off
Leave fuel cap off and filter submerged. Ether fish out the fuel return or at least position where it's visible. Then press the purge bulb several times. Fuel should spurt out the return. If no fuel from return line and air bubbles come from filter, lines are reversed somewhere.
11/1/2023 3:28:05 PM •
Garden
•
Answered
on Nov 01, 2023
•
26 views
Living Accents Assembly guide for 8048106 pergola
1. Place the Pergola structure onto a flat surface in an area with adequate space for assembly and use.
2. Unwrap the hardware bag (included with the pergola) and place the contents on the flat surface near the structure.
3. Begin the assembly by attaching one of the long side rails to the top of the Pergola. Insert the rail into the slot at the top of the structure. Securing it with the provided hardware. Tighten the four screws using a drill to firmly secure the rail in place.
4. Next attach the second long side rail in the same fashion.
5. With both side rails firmly in place, attach the short side rails. Insert the rail into the slot at the top of the structure and then secure it with the provided hardware. Tighten the screws using a drill to firmly secure the rail in place.
6. Repeat this same process to attach the remaining short side rail.
7. Attach the four corner brackets using the provided lag bolts and washers. Some models may require different hardware for this step.
8. Secure the corner brackets with the provided bolts and washers.
9. Attach the remaining lag bolts into the holes in the top of the Pergola frame.
10. Tighten all the screws and bolts using a drill which will secure the frame in place.
11. Place the canopy (sold separately) on the top of the Pergola frame and secure it using the provided hardware and tools.
12. Once the canopy is secured in place.
10/31/2023 3:23:34 PM •
Garden
•
Answered
on Oct 31, 2023
•
31 views
Tiller tines don't turn when I throttle?
Here are some possible causes and solutions:
Belt Issues: If the drive belt is broken or loose, the tines won't turn. Check the belt tension and replace the belt if necessary .
Idler Assembly: If the idler assembly is not properly tensioning the drive belt, the tines won't turn. Adjust the idler assembly or replace it if necessary .
Engagement Cable: If the engagement cable is loose or not tensioned properly, it may need to be tightened or replaced altogether .
Transmission Issues: If there is an issue with the transmission, such as a broken gear, the tines won't turn. Stop using the machine immediately and inspect the transmission .
Since you mentioned that your tiller tines were turning fast after replacing the carburetor and then stopped turning after connecting the throttle cable, it's possible that there is an issue with the engagement cable. You may want to check if it's properly tensioned and connected to ensure that it's not causing any issues
How To Fix Tines That Will Not Move - Tiller Repair
10/31/2023 4:16:29 AM •
Garden
•
Answered
on Oct 31, 2023
•
39 views
Why does blower only run w choke half on
Typical carburetor low speed circuit is blocked but can be fuel or other. Likely needs carb adjust, clean and/or rebuild.
10/27/2023 12:19:48 PM •
Garden
•
Answered
on Oct 27, 2023
•
37 views
How do I tell what year model my Kabota RTV900 XT is?
https://www.google.com/url?sa=t&rct=j&q=&esrc=s&source=web&cd=&cad=rja&uact=8&ved=2ahUKEwjF7pm4xpSCAxVEmIkEHaPbAvoQFnoECB0QAQ&url=https%3A%2F%2Fwww.orangetractortalks.com%2Fforums%2Fthreads%2Fcan-i-determine-what-model-year-from-serial-code.45724%2F&usg=AOvVaw320X8niJs2M0dRBU5lxjT6&opi=89978449
10/26/2023 8:28:04 PM •
Garden
•
Answered
on Oct 26, 2023
•
31 views
Which wires to connect to a new solenoid on Dixon ztr 4516k?
The solenoid should have three posts. Two large contactor lugs and a smaller terminal for control (batt pos). The solenoid frame must be securely attached to the mower chassis as it is the control winding return path (batt neg).
The large gauge red wire from the positive battery post and 2 smaller red wires stack on to one contactor lug (post 1). The other large gauge red wire from the starter goes to the other contactor lug (post 2). The small yellow wire goes to the smaller solenoid control terminal (center post) and energizes the relay with battery positive from the ignition switch S (start) terminal.
Refer to attachment, wiring diagram.
10/16/2023 12:32:37 AM •
Garden
•
Answered
on Oct 16, 2023
•
40 views
What is the best wood material to build a storage shed?
Tanalized pressure treated cedar Joe. It looks nice, smells great and holds up well in the weather. If you don't stain it, the finish will go a soft grey, and if you want to bring it back, you can pressure wash it. Larch if you can get it, comes second. My waterwheel in England was cast iron, but the timber was Larch, and it lasted really well.
I hope you are doing well Joe and as it is Thanksgiving weekend in Canada, I will wish you a good one in advance!
..
10/7/2023 4:45:18 PM •
Garden
•
Answered
on Oct 07, 2023
•
26 views
JD 185,Starter turns but not starting,power but no spark. Blade switch off. Now what do I check?
Spark requires ignition switch in run or start and operator in seat. Try disconnecting the seat switch.
If still no spark check the green wire at the ignition switch terminal M (magneto) for continuity to battery negative (ground). With ignition switch in the off position the green wire will have continuity to ground. In any other position it should be open or high impedance.
Comment for further assistance.
10/3/2023 4:32:05 PM •
Garden
•
Answered
on Oct 03, 2023
•
53 views
Not finding what you are looking for?