20 Most Recent Dewalt heavy - duty6" right angle random orbit sanderwith electronic variable speed DW443 - Page 4 Questions & Answers


Time to replace a few orings in the trigger valve. There are at least three orings made of vinyl that fail, two on the trigger pin and one on the plunger.

Dewalt Tools &... | Answered on May 06, 2016


If it works when upright, perhaps the nose piece is not fully depressed. I have the same problem using my pneumatic finish gun.

Dewalt Tools &... | Answered on Apr 17, 2016


If you have a long enough shaft you can grab onto it with a pipe wrench or vice grip while using an open end on the large nut. You may be able to get it into a bench vice as well. These quite often have lock tight on them as well. Heating may help you out but you will have to move quick.

Dewalt Tools &... | Answered on Feb 10, 2016


If the light keeps flashing then the battery is not charged enough to fire the gun. recharge the battery or buy a new one if it continues.

Dewalt Tools &... | Answered on Jan 10, 2016

Tip

Modified stator field


dw712 crosscut saw miter saw i have had a problem with the motor stator electric field and i was surprised by the MODIFICATION not seen if you don,t know about that this machine has undergone by the later builds of the same type .
Because the difference was not to find in the diagram and ordernumber of this stator field , because the older model has only 2 connecting wires,, and the later modified model has a stator field with 4 connecting wires . it has also a different ordernumber and is also a little bit more expensive.
So be warned when ordering a statorfield check the stator after 2 or 4 stator contacts advance order , it can has also be modified in the usa on the same way . !! i have also have asked for made changes on a diagram by Stanley/Dewalt (England) in between 1 hour they have made an change for it , for a powertool that was missing a type of [ model DC837 type 1] type 10 and 11 where the only ones to see there but type 1 was missing and the switch for that model was a problem but they have special made a kit for it because of the modified switch .


DW712 VERSTEKZAAGType 1

on Nov 24, 2015 | Dewalt Tools & Hardware - Others


the vanes in the small air motor are stuck
try a small amount ( couple of drops ) of sewing machine oil in the air inlet and see it it will spin
you may need to bump the pad on the bench to jar the shaft to start rotating

Dewalt Tools &... | Answered on Nov 04, 2015


If you release the belt that would give you more room to get the cord out. When you releas the belt it brings the rollers together which loosens the belt.

Dewalt Tools &... | Answered on Aug 05, 2015


I've been using dewalt tools exclusively for 15 years. I've fixed numerous drivers, sawzals, etc. I've learn 3 things over and over again. 1 cleaning & lubing are grossly under rated, 2 if one part goes the rest are not far behind & 3 it has never cost me more than $20 to $30 bucks more to have the repair place rebuild it than to fix it myself. And most times they give you a new bulk packaged tool as a rebuilt. My recommendation: have it rebuilt...enjoy the new tool.

Dewalt Tools &... | Answered on Jun 27, 2015


how old is the battery, test and recharge, if ok make sure is well oiled. May have to have it serviced if it is still low on torque.

Dewalt Tools &... | Answered on May 20, 2015


I would suggest giving our Service Center so we can get your unit looked at. DEWALT com

Dewalt Tools &... | Answered on Mar 20, 2015


Make sure the brads are not too small for the gun.

Dewalt Tools &... | Answered on Mar 18, 2015


What model gun is this? Framing, finish, battery powered?

Dewalt Tools &... | Answered on Mar 13, 2015


Power? circuit breaker? Plug? Owner's manual. Troubleshooting
Does the motor hum? if so you have something jamed in the planer cutter.

Dewalt Tools &... | Answered on Feb 28, 2015


Brushes can definitely cause this but unless you feel fairly confident in pulling the unit apart, it may be more cost effective to just replace it. It would be unusual to see the brushes wear out so quickly but I do not know how much you use it or the load you put it under. I have a Rigid that I use a LOT and have had it for probably 5 - 6 years and it is holding strong. These things just tend to last. I would contact DeWalt and see if you can have them send you new brushes first and then go for it; the worst is that you ultimately have to replace it (which you might have had to anyway) and the upshot is that you fixed it yourself and now have many more years and sawdust sneezes in your future.

Dewalt Tools &... | Answered on Feb 14, 2015

Not finding what you are looking for?
Dewalt heavy - duty6" right angle random orbit sanderwith electronic variable speed DW443 Logo

1 questions posted

Ask a Question

Usually answered in minutes!

Top Dewalt Tools & Hardware - Others Experts

John Trevino

Level 3 Expert

1420 Answers

Ruben Bustamante

Level 2 Expert

120 Answers

john h

Level 3 Expert

22486 Answers

Are you a Dewalt Tool and Hardware - Other Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Dewalt Tools & Hardware - Others

  • Dewalt Tools & Hardware - Others

Most Popular Question

replace sanding pad random orbital

  • Tools & Hardware - Others
Loading...