Top 10 Husqvarna Lawn Tractor 48" Deck, 23 Hp, Model# Yth2348 Questions & Answers

Husqvarna Lawn Tractor 48" Deck, 23 Hp, Model# Yth2348 Logo

Question

  • 52,777 People Helped

My Husqvarna Hydrostatic transmission is not

My Husqvarna Hydrostatic transmission is not delivering the consistent drive power that it once had. It is stopping going up small inclines. I have replaced the drive belt with no improvement. I am planning on checking the torque spring to see if that helps but I was wondering if there was some other adjustments that I can perform to hopefully rectify the issue. My tractor is a YTH 150

Posted by on

Answer

  • Most Helpful of 9 Answers

Try this - remove all the transmission oil from the transaxle and put in a heavyer oil - 50 wt.
see if your transaxle has a drain plug - if not you will need to remove the tranaxle from the lawn tractor. I had to try a ratchet strap to the rear of the tractor and lift it up until the wheels were free. I removed the brake linkage spring, the fwd/rev linkage, and wheels. Undo the axle bolts and two screws ofn the cross support bracket on the tranaxle mount. pull the vent fill plug on top of the transaxle and turn the transaxle upside down to drain all the oil from it into a pan. Refill with 50 wt. to the top and remount the transaxle back in place. Next you will need to bleed the system as follows:
1. Have the tractor on jack stands with rear wheel off the floor.
2. Start engine on low speed.
3. repeat open and closeing the bypass valve while alternating the forward and reverse pedals.
4. when wheels start to turn increase the engine speed.
5. repeat quick forward or reverse with panic braking stops until transaxle gets full responce.
6. remove jack stands and have tractor on the wheels.
7. recheck the oil level again.

I did this to mine and it will improve your tractor ability to climb hills like new. 30 wt oil is too light (good for brake in) when tractor was new and refilling it with 50 wt will work like new or better.

Posted on Aug 02, 2009

Question

  • 11,179 People Helped

belt installation diagram for a husqvarna riding

belt installation diagram for a husqvarna riding lawn mower

Posted by on

Answer

  • Most Helpful of 1 Answers

Depending on the year - here is the link for manual that will show the diagram

http://weborder.husqvarna.com/order_static/doc/usa/2009/I09000/I0902011.pdf

If you have any questions, please call John at 860.233.5439 x222 or visit www.ButlerPower.com

Posted on Sep 06, 2010

Question

  • 9,003 People Helped

Husqvarna won't go forward or backwards.

Husqvarna won't go forward or backwards.

Posted by on

Answer

  • Most Helpful of 1 Answers

Thanks for the points on the pulley system. I somehow disengaged the pulley when putting on the brake.to put it back on easily, I reengaged the brake with my hand and slid the belt back over the pulley wheel on the other side, now located more toward the middle of the mower in arm's reach. Very quick fix to an alarming symptom!
5_19_2019_8_29_33_pm.jpg

Posted on May 19, 2019

Question

  • 8,718 People Helped

I NEED BELT DIAGRAM FOR MY HUSQVARNA RIDING MOWER

Problems with Husqvarna Lawn Tractor 48" Deck, 23 Hp, Model# Yth2348

The belt has come off and I need to know how to reinstall it. A spring came loose when the belt that drives the blades came off.

Posted by on

Answer

  • Most Helpful of 2 Answers

http://www.usa.husqvarna.com/home.aspx try this out for your answers, I hope this helps you. MERRY CHRISTMAS!

Posted on Dec 23, 2008

Question

  • 7,923 People Helped

how to replace drive belt

need to know how to replace drive belt on cth 200 husqvarna ride on mower

Posted by on

Answer

  • Most Helpful of 1 Answers

here is a diagram that will hopefully help you. let me know if it helps, or if you need further assistance. thanks.

convert?ilfn=d%3a%5cempartweb_52%5ccatalog%20data%5cemp_img%5chus%5cimages%5c33%5c28%5c0009.tif&ilsc=16&iliv=0&ilbr=0&ilif=g&ilre=8

Posted on Mar 15, 2009

Question

  • 7,175 People Helped

what kind of oil for a husqvarna riding mower?

I need to make sure I am using the right oil for my brothers Husqvarna riding mower. Do I use SAE 30? It is a riding mower Model # LOGTH2448T. The engine is a Briggs and Stratton Intek 24 Twin OHV (?) 

Posted by on

Answer

  • Most Helpful of 3 Answers

Yes SAE 30 is the recommended oil for B & S engines. You can find it on amazon for good price. here: Amazon com oil 30w . Hope this was helpful. cheers

Posted on Dec 03, 2014

Question

  • 6,028 People Helped

Husqvarna zero turn mower won't start

I have a Husqvarna zero turn mower that won't start...it just makes a clicking noise. It has less than 15 hrs usage, but has been sitting for over a year. Would this be a problem with the ignition or the starter? Thank

Posted by on

Answer

  • Most Helpful of 1 Answers

Usually if all you hear is a clicking noise, it is the solenoid itself that has gone bad...if you can jump the solenoid and the mower turns over, it is the solenoid.

Posted on May 03, 2009

Question

  • 5,787 People Helped

How do I adjust the deck level on a Husqvarna

How do I adjust the deck level on a Husqvarna riding mower?

Posted by on

Answer

  • Most Helpful of 1 Answers

Not sure if you are looking for the nuts and knobs or how to level? Most newer decks have knobs for adjuctments. I park my mower on a concrete level surface make sure all tires are at the correct psi then with tape measure check front left and right at bottom of deck for same measurment. You can also put a 2 ft level on the deck and adjust.

Posted on Mar 13, 2010

Question

  • 5,061 People Helped

Blades will not engage on Husqvarna riding mower.

Our Husqvarna mower is less than 1 year old. It starts easy, the deck will engage but the blades will not engage. What to do???

Posted by on

Answer

  • Most Helpful of 2 Answers

Could be a broken belt, loose belt (stretched) or something is under the mower deck jamming the blades. (stick for an example)

Posted on Apr 15, 2010

Question

  • 3,768 People Helped

I have a Husqvarna YTH 2348 the deck anti sway bar

I have a Husqvarna YTH 2348 the deck anti sway bar came looses fell of frame and bent, I removed rod strightened and need to kown how to put rod back in proper location on the frame and deck bracket

Posted by on

Answer

  • Most Helpful of 3 Answers

Once you've straightened it - you've finished the hard part. Now take the end without the pin and stick it into the hole located on the transmission frame (the metal piece that the transmission sits on.) It is directly under the seat. The hole is on the front side of the tranny frame. Once you have it all the way in, take the pin end and put it through the mower deck brace (right side.) There is a hole there also for this end. If it doesn't go through enough to get the washer and pin through, push the mower deck towards the anti-sway bar. It should give a lot since the anti-sway bar is off. Once you fasten it, your'e done!

I only know this because it just happened to me today. I have the same mower as you, so I thought I would share.

Posted on Jul 04, 2009

778 questions posted

Ask a Question

Usually answered in minutes!

Top Husqvarna Garden Experts

J. Bradshaw

Level 2 Expert

121 Answers

lnbn1975

Level 2 Expert

204 Answers

Marvin
Marvin

Level 3 Expert

85178 Answers

Are you a Husqvarna Garden Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Lawn Tractor 48" Deck, 23 Hp, Model# Yth2348 Husqvarna

  • Lawn Tractor 48" Deck, 23 Hp, Model# Yth2348 Husqvarna

Most Popular Question

husqvarna hydrostatic transmission not

  • Garden
Loading...