Top 20 Husqvarna Lawn Tractor 48" Deck, 23 Hp, Model# Yth2348 Questions & Answers

Question edited for a lot more clarity. Question moved from Cars and Trucks. The part is here. Available form eBay or other fine mower spares suppliers. You can also get a repair kit for it.

Carburetor Carb For Husqvarna YTH22V42LS Lawn Tractor

eBay https://www.ebay.com > ... > Carburetors Carburetor Carb For Husqvarna YTH22V42LS Lawn Tractor ; Manufacturer Part Number. Does Not Apply ; Accurate description. 4.9 ; Reasonable shipping cost. 4.7. US$69.99 · ‎In stock

Carburetor Rebuild Repair Kit For Husqvarna ... - eBay

eBay https://www.ebay.com > ... > Carburetor Parts Find many great new & used options and get the best deals for Carburetor Rebuild Repair Kit For Husqvarna YTH22V42LS Lawn Tractor at the best online prices ... US$21.99 · ‎In stock

Replaces Husqvarna YTH22V42LS Lawn Tractor Carburetor

Mower Parts Land https://mowerpartsland.com > Shop Jun 22, 2022 - Replaces Husqvarna YTH22V42LS Lawn Tractor Carburetor. $113.79 $63.79 ... Includes 1 New Replacement Husqvarna YTH22V42LS Lawn Tractor Carburetor. US$63.79 https://www.google.com/search?q=yth22v42ls+husqvarna+carburetor+replacement ..

Can you show a picture of the back of the switch (connector side) and I may be able to help.

i would say you have a blockage in the fuel system. possible dirty carburetor. check carb bowl if you see any dirt or water. take off and clean. be sure fuel lines and filter are good. check air filter also.

check to see if choke plate is closing all the way

Locate the red wire on your battery and trace it to your starter solenoid. There normally is another smaller red wire from the starter solenoid that is connected to the equipment's fuse. Check if fuse is okay by visual means or with a multimeter (set on resistance scale). If fuse is okay, check red wire from battery to the fuse for continuity. Good luck.

You should remove the pulley from the top. Should connect with one nut. Be very careful to see if a washer is used, if so, it should go back in the same order you remove it.

This seems to be the correct part no. for the 36" deck, is the belt definitley the correct one, it should have the no. 174978 marked on it.

To freewheel the tractor using the freewheel lever at the rear of the tractor would not damage the tractor. Check your belts and make sure the lever is all the way back in.

The problem with an electric cluch is that when the engine is running without the clutch engaged the clutch can turn into a dynamo which then passes power back up to the switch, most machines will have a diode close to the clutch in the wireing to stop the current flowing back to the switch, so i guess the diode is bad on your machine and power is flowing back to the switch and melting it,

get an accredited mower repair shop to check the charging circuit

Sounds like a weak coil. When cold it's good when hot it loses spark.

be sure it is the correct one for that mower and it is on correctly and it is from a lawn mower parts store. not one from tractor supply or rural king.

the brand huskee is now manufactured by MTD Parts are available from tractor supply company at www.tractorsupply.com there are pages of not very encouraging reviews about the huskee mower or about the tractor supply company but you can contact them to see what you can get as for the problem , if it is a zero turn unit it may be a clutch arrangement needs adjustment If you do not get any help from that company, you could ring around the mower repairs shops to get an idea as what could be wrong as the principle of operation will be the same . also there are sites that have pdf versions of the workshop manual for huskee

Hi,it could well be the battery,it would not hert to put battery on charge and try to start it again,all the best.

The belts will be different in lenght and the corret lenght is very important for proper function.

recheck free wheel rod may not have engaged ---

Some of those are adjusted by bending the tie rod.

Yes take it to the dealer and have them check the pump since it uses hydraulic motors, it sounds very much like the pump is running backwards or is it possible the blades are on upside down

Ok, this has happened to me before and it was a broken deck engagement wire. On some models the deck engagement wire which leads to the deck from the pto engagement lever is routed on a critical bend. Because the wire in the casing is bending at such an odd angle it can ware through the casing and break. If this happens it will cause the deck break to come on and stop the deck belt from turning in the pulleys. Check to see if this wire has broken. If so you can order the new part from a small engine mechanic or from the vendor or manufacturer. When you hook up the new on route the wire same as the old, but make sure that it does not have such a tight bend in the casing. hope this helps :)

Have you tried to jump across the solenoid? It could be different things causing your problem. It could be a broken wire, the switch, the solenoid or even as simple as a blown fuse. What have you tried?