Top 20 Jura Capresso Jura / Capresso Grinder Questions & Answers

Unfortunately, without being there in person to inspect the machine and its components, it's difficult for me to provide a definitive answer. However, I can offer some general guidance that may help:

1. Consult the user manual: The user manual for your Capresso C3000 should have a diagram or schematic showing the different components and their connections. If you still have the manual, check to see if there's a helpful diagram inside.
2. Look for visual cues: While it can be difficult to identify the tubes by sight alone, there may be visual cues that can help you narrow down which tubes go where. For example, one tube may be thicker or more flexible than the others, or it may have a different color or texture.
3. Experiment with different configurations: If you're unable to find a diagram or visual cues, you may need to experiment with different configurations until you find the correct one. This can be time-consuming and frustrating, but it may be the only option if you're unable to find any other information.
4. Seek professional help: If you're still unable to identify the correct tube configuration, you may want to consider seeking professional help. A qualified technician or repair service may be able to identify the correct configuration and get your machine back up and running.

I hope this helps, and I wish you the best of luck in getting your Capresso C3000 back in working order!

http://www.fixya.com/support/t12615678-capresso_303_will_not_steam

Talk him

Rinsing cycle at start up is electronically programmed function. Unplugging is a temporary solution. Jura will not sell parts or offer any guidance. I could look into more details to find an answer but the model Capressa 50 is not listed in my Data base. Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/edward_bbd2c7ff4ee1828a

TRY SWITCHING IT OFF AND RETRY LATER MAY BE IT WILL RESET IF NOT CHECK FOR ERROR OR TELL US MORE ABOUT THE FOULT

The first thing to check is the seating of your water tank. Just a few grains of coffee grounds or dirt underneath the tank are enough to break the watertight seal. Make sure the area under the tank is absolutely clean. That's always worked for me when I've had the leaking problem.

You really don't give which machine - but here is link to company product support. Maybe they will have product manual to help trouble shoot issue. Sorry could not of been more help Product Support

What model do you have? What's the problem you are trying to fix by resetting it?

Just a guess here but if you are not using soft water you may have a hard water scale coating on the sensor. The sensor is preventing the heating element from powering up because it thinks there is no water. Try filling the machine with vinegar for several hours (no more than overnight) This will dissolve hard water deposits and hopefully clear the sensor. (the sensor should be a simple continuity contact. If you can look inside and see a metal button and it is fouled clean it off.)

Try running distilled white vinegar through it.

Try applying hot water around the dish to expand and unstuck while gently but firmly pull the tray. It went in so must come out.

constant heating message on screen is from a thermal fuse blown on one of the boilers. service call required i'm afraid...... very cheap part about 10 euro

http://www.nordson.com/en-us/divisions/asymtek/documents/Manuals/392771am620isb.pdf All the best Kolbrun Descaling is there

I just opened up my Jura Capresso C1500 Machine. It's a little tricky, but here is how I did it. I gently pryed the front part of the top off. There is a tab connector in the very front of the oval in front center. Lift (or gently pry with a flat head screwdriver) straight up until it comes free. There are several other tabs that will lift straight up on both sides of the top. However, there are two tabs in the back (one on either side where you see the black pins protruding out the back top of the machine) that are encircled around the pins. The only way I could get those off was by gently prying until the tabs snapped off cleanly. I pryed the one on the right first, and it stayed intact except for breaking off the bottom of the circle; so it will actually still snap into place back over the pin. To free the left tab I simply lifted the lid up and down several times until it snapped off cleanly. There are so many other tabs that fit tightly into rectangle-shaped sockets that breaking the back two did not change my machine's appearance or function. Once the top was off, you can access a lot of its workings including the grinder, top water tube, spout, etc. I use dark beans that are slightly oily so I took off the bean compartment, silicone funnel ring, and attachments and cleaned them thoroughly with hot, soapy water. We found a pebble or two in our beans through the 8 years we have used it and I think they have done some damage on the grinder.

Hi Marton Registered repairers love you guys.... If you carry a smartphone these days and most of us do. You need to learn to take photo's first. Even the Las Vegas pro restoration guy on TV does that. Sorry I don't have those photos and you'll be really lucky is someone on Fixya does. Try YouTube videos.

The machine gives the massage that you need to fill coffee beans when the grinder motor rotate more freely than it should be when the beens are inside the griders disks. The problem you describe is very frequent and is due that the beens even you have cleaned it as you mention they don't make it up to the grinders disks. So if the grinding disk are not damage by any reason - like over heated or arecoven with coffee beans oil and coffee remains- you can try first to udjust the grider to more gross grinding by rotating the upper disk with special tool. With this you will give the chance to absorbe in the disk more easiy the beans. Also if you manage to grind some beans more gross this will also be used as a cleaning product for the disk and flush out any oil or cofee remains stuck inside the grinding disk. You can turn us much you will need to see the bean been grinded but as an advice use a marking pen and make a marke where the grinder udjustment is before you do anything since you will have to turn back the udjustment to the same point after you fix the problem. If you fix it like this then you have to turn it back at original place but only by small steps at a time then make a coffee and then turn again a litle bit. By this you will avoid blocking the disk with grounded coffee and you will have to do everything from the begining.
If all the above does not have any results then you will have to desasemble the grider and brush the disk so they are clean and put them back together.
Their is a very small posibility that the electronic is faulty but this is very very rair, so give emfasis to the first solutions

Error Code 4 is related to the heating sensor.

If it's currently in a cold room then switch off and move to a warm room (>65 Deg F) for a couple of hours and try again to see if you get the Error message.

Most of the time when this problem happens, then it is the hose is plugged up. And ne to be descaled. Have you descaled the machine lately?

email to Jura, they will send you a copy of the manual for free!

The switch or photo sensor is not sensing any beans present. So it can't continue Use torch to inspect bean entry area Small brush etc