Linksys WRT160N Wireless Router - Answered Questions & Fixed issues

You are using WRT160N router. This router has issues with the firmware.
Try to upgrade the firmware of the router. Firmware is the software of the router.
Download the latest firmware of the router. Go to the manufacturer's web site and download the firmware of the router.
Open the set up page of the router and upgrade the firmware of the router. Once you upgrade the firmware of the router, reset the router.
On the router you will find a small reset button, hold it down for 30 seconds. release it. wait for 1 minute. Now unplug the power to the router and plug it back in.
Now you will need to reconfigure the router according to the Internet service provider.

You will need to install an WIFI extender in the front room of your office which will then extend the signal to the rest of the out building. I've included a link on Amazon to a very simple, easy to set-up extender that you can set-up with the push of a button. Once you set-up/configured the extender near your existing router following the simple instructions, you can then move it to the front of your office. Best of luck! Amazon com TP Link N300 Wi Fi Range Extender AP mode Supported TL WA855RE...

The general rule for WiFi is to have the router placed at a reasonable height above the items that wish to use it. This is because the radio waves travel downwards It was probably a repeater that was recommended to boost the signal.

More info, you have a modem/router and another router? and what is "both" independently? and "while they are both connected" both what? If you just have one box the modem router, disable bridge mode or you just have a modem then with no routing.

Be like that other Linksys router model, Linksys WRT160N router is always unique because of their wild, future-oriented functions and even smaller size. You can call on the Linksys support number in order to get help from the expert to start running the router again. If the number you have dialed is not giving any response, you can go to the Contactforhelp to acquire the alternate contact number of technicians. Linksys setup customer support phone number Technical Service USA

http://www.polarcloud.com/tomato

1.With an online-capable game inserted into your Nintendo DS, turn on your system and access the game's main menu. 2.Access the Nintendo Wi-Fi Connection settings. -These settings are typically found by selecting "Nintendo WFC" from the game's main menu. For detailed directions, consult the manual for the game. 3.At the Setup screen, tap "Nintendo Wi-Fi Connection Settings." 4.Tap a connection file labeled "None." -If no empty connection files are available, select "Erase Settings" followed by "OK" to create an empty connection file. 5.Tap on "Search for an Access Point." 6.The Nintendo DS will search for any wireless networks within range. Once it is finished searching, it will display the names of all the wireless networks it finds. oIf you receive the error message "No Compatible Access Points Within Range," click here. 7.Tap on the name of your wireless router or access point. oIf there is a gray padlock next to the name of the wireless access point you wish to connect with, this indicates your router is using a security type incompatible with the Nintendo DS. If prompted, use the keyboard on the bottom screen to enter the password for your wireless router or access point. 8.Select "OK," "Save Settings," and then "Yes." The Nintendo DS will run a connection test. 9.The connection test was successful - Your Nintendo DS is now connected online. Situation Not Resolved: If the connection test was not successful, you will receive an error code: ·Error Code 51300: This means the security code or network name entered into the Nintendo DS is not the same one the router is set to. To reach your connection settings, click "back" on the error code screen. Make sure to pay extra attention to the security key you find in your router's settings and enter it exactly as it appears (the key is case sensitive).

Call Linksys Technical Support. If they cannot help try this http://technicalsupport.blog.friendster.com

Linksys WRT160N Wireless Router installation

refresh your wireless connection by turning off the wireless switch of your laptop and then turning back after 30 sec.

Power off all of your network devices, including modem, router, and computers. Then power on each device in the following order:

1. Cable or DSL modem
2. Router
3. Computer

Wait for about 1 minute between each step, do each device has the chance to fully power up. This will reset the connection from your modem to your router and force the router to refresh it's settings. Please let me know if fixed your problem.

If you have any more questions, just come back here and leave a comment - I'm happy to help.

i think this can be fixed . first reset the router settings and reset the printer also. and now try to setup the connection with advance settings as manual says . for more help contact brother Printer Tech Support . i hope this will help thanks

Setup wireless network by getting to the router page Enter this ip address in the address bar as 192.168.1.1 Hit the wireless tab and type network name in wireless network name. Once you click on save settings your network is ready to use Also secure the network by clicking on the wireless security and clisk on the security tab to protect your network.

Your Linksys router default password is ADMIN

Its ADMIN

Roter default password is ADMIN

Download this from linksys site. please follow the link. Linksys Support

Please reset the router by pressing the reset button on the router for 30 seconds and again configure the router.

Please check on the status tab that the what is the internet ip address you are getting from the page. The ip adress is if 192.168.1. then you have to change the router ip address to 192.168.2.1 on the very first page setup under the router ip address.

Linksys Support WRT160N Click downloads and choose the appropriate download for your version.