20 Most Recent
Linksys WRT160N Wireless Router - Page 3 Questions & Answers
Wont let xbox on live
You need to configure the router for port forwarding. Here is the definitive source to assist you: http://portforward.com/english/routers/port_forwarding/Linksys/WRT160N/Xbox_Live_360.htm
Computer crashed had to wipe out and need to
You really shouldn't need an installation disk to install this router. here is a link to everything available from linksys. Review the user manual for any questions about the product. Also there are no drivers needed. Everything is either wired or wireless. To access the settings you just enter the appropriate IP into your browser. All of this can be found in the manual.
http://www.linksysbycisco.com/US/en/products/WRT160Nthank you,
lee
WRT160N current time not available
Log on to your router as the administrator. On the setup screen, set the correct time zone and save your settings. If you have your router properly installed and set up (using the wizard or the manual), the correct router time will be shown on the Router screen. Router time is obtained from the internet automatically, so the time should be correct unless it is being blocked by a setting or some other device.
If you do not have a copy of your manual, you may obtain one here: http://downloads.linksys.com/downloads/userguide/1224640959708/WRT160N_V10_UG_A-WEB.pdf
HOW DO I FIGURE OUT MY PASSWORD
Hello! The WRT160N default password is admin, with no user name. If you changed the password and you forgot it you can return to the factory default settings. For this, you just have to press & hold the router reset button at least 20 seconds (it's located in the back side of the router) and then you can log in again (with no username and the password "admin" - of course, without the quotes). Hope this helps!
Forgot pass word
This is easy to resolve,you need to reset your router back to factory default.Using the reset button on the rear of the router,press and hold button with power cord applied for 15 seconds,remove power cord for 15 seconds then replace power cord for additional 15 seconds without removing your finger from the button.This could take up to 30 seconds each time but remember to do the steps as outlined and when you are finished your router should be reset to factory . Factory user name is admin and password is password
I've got a Linksys WRT160N V2 router that stopped
Connect your router to computer with ethernet cable then you can access it with following default link. http://192.168.1.1 or http://192.168.0.1 or http://192.168.15.1 or http://192.168.2.1 If you are not able to access it with above ip then check your computers ip address gateway ip is your router ip try with it. Then it ask for user name and password. Type user as "admin" and password as "admin" or "password" or blank. Then you can see configuration page of router. Then configure wan settings and lan settings enable wireless if you want to use wifi Then save settings and restart router Then connect cable from internet service provider to WAN port of router and connect ethenet lan cable from computer to lan port of router. . Let me know if you need further assistance. Thanks for using FixYa.
Wrt160n shows offline
I would start by contacting your internet provider and having them ping your modem. If there is a connectivity problem, they should be able to help. You may also want to try resetting your router; and start again from a clean slate. Your picture shows that the modem is not connected to the internet, and your router is not connected to you modem.
Where is wps on Belkin n1 vision?
Before you will be able to use this function, you will have to log into your router and enable WPS push button in the security settings.
Using Wi-Fi Protected Setup
WPS uses WPA2 (described below) for encryption. It does not
provide additional security, but rather, standardizes the method for
securing your wireless network. You may use either the Push Button
Configuration (PBC) method or PIN method to allow a device access to your wireless network. Conceptually, the two methods work as follows:
PBC: Push and hold the WPS button located on the back of your N1
Vision for three seconds. Then, initiate the WPS procedure on the client device within two minutes. Refer to your client's documentation on this procedure. Pushing the PBC button will automatically enable WP
Samsung Blueray DVD wireless
Put the mac address of the bluray player in the wireless setup section of the router then enable mac filter. that should do it.
Tag was removed with pin number for my linksys mod
You can find your WiFi security info by logging into the router
Out of the box your SSID should be Linksys
You will have to be connected with an Ethernet cable or use a computer that is already connected to your WiFi network.
1.Open a web browser and enter 192.168.1.1
2.You will get a login page for your router. Usually the login formation is as follows:
admin/admin
3.Once you have logged in you want to locate the wireless menu on the page.
4.Here you will find the pin for your wifi network
How to open nat on a pk5001a modem
you must read your owner manual, and follw the instruction or download the instr. manual from www. retrevo.com .However see the troubleshooting chart.God bless you
Can't connect wifi to my iPhone
The problem is with the IPhone not the router. check with apple.com for an answer to your problem. Apple devices are very problematic when connection to some WiFi devices. BTW, NEVER post your username and password of any device in a public forum. If a hacker has any idea of your location, you just made it very easy for them to hack your network. I would change both the username and password for your own safety
Not finding what you are looking for?