20 Most Recent HP OfficeJet J4580 All-In-One Laser Printer - Page 4 Questions & Answers

Uninstall the printer then re boot Pc and reinstall the printer with the disk it is the only way to get it back up ,that is if it is not damaged. Thanks for asking FixYa please rate my solution and give testimonial this is how i earn my achievements here on FixYa Thanks in advance

See free PDF manual http://www.manualowl.com

You need to install the printer driver.You can download the HP printer drivers from their supportWEB site. Please click on this link and select your model printer to download:-http://welcome.hp.com/country/us/en/support.html

HiTry disconnecting the printer and leaving it for a while.[to reset]Connect it again.

HiTry uninstalling the printer drivers and reinstall them afresh.You can download the drivers from the link below if you don't have the installation discs.h10025.www1.hp.com/ewfrf/wc/softwareCategory?cc=us&lc=en&dlc=en&product=3645100Hope it helps.

Hello Sharon! Welcome to FixYa!Tri color cartridge problems sometimes occur in HP printers, there are some troubleshooting steps which may solve this problem:-Some times this problem is solved by cleaning the contact of color cartridge.For this Take the cartridge out and clean the contacts off with something (ie: pencil eraser, your thumb), It may solve the problem.If problem still exist then Partial resetting sometimes resolve this issue, You must follow the given steps to Partial Reset it:-Disconnect the power cord from the back of the printer, and then wait for 20 seconds.Press and hold # and 3 on the printer control panel while connecting the power cord to the back of the printer Release the buttons when the printer turns on. The reset is complete.I hope this resolve the issue, But unfortunately if problem still exist then it may because of some hardware issue of Tri Color Cartridge. If your printer is still in warranty then claim the warranty. If it is out of warranty then you have to contact authorized service center of HP Printers to solve this problemI hope this solution helps you and you have clear picture in your mind nowLet me know if you have any confusion in your mind.Sir, Your Rating as FIVE Stars for this solution and words of appreciation will be esteemedThank You for taking my service Concerned: Muhammad Uzair Team : FixYa

Browse the link, down load the drivers..http://h10025.www1.hp.com/ewfrf/wc/softwareDownloadIndex?softwareitem=mp-77039-1&cc=us&dlc=en&lc=en&os=4062&product=3645100&sw_lang=

In most cases the printer driver software can have errors while being in use or is shut down. So to reset remove your printer from the PC and uninstall the printer software. Now reinstall the printer software and then connect the Printer ONLY WHEN PROMPTED, to be detected as a new hardware as it will be installed.

DONT CONNECT PRINTER WHILE INSTALLING PRINTER SOFTWARE....IN THE MIDDLE OF INSTALLATION IT ASKS TO CONNECT PRINTER.............
THEN ONLY INSTALLED PROPERLY

surely you got software with the all in one printer. if you have plugged in the printer before you installed the software then this sort of thing happens. if this is the case them un install the the printer completely switch off the pc wait ten seconds and reboot the system them install the software without the printer in. once software is installed then plug in your printer and the pc should recognise it.

The ink head for the ink cartridge is likely to have been scratched by something that was on top of another piece of paper that went in. When this happens the solution is usually to replace the ink cartridge, however if it is possible you may remove it and try to see if there are any small objects jammed against it (such as tiny pieces of paper or bits of dust).

Replace tri color cartridge..But ensure that mono cartridge must be in good health printing condition,other wise alignment won't completes..

Hello Paul crisp,To change the language on your printer you need to:-

• Turn on the printer.
• Press the *and # buttons.Release the buttons.
• *******##### will be displayed.
• Now press buttons 1,2 and 3 until there appears the resetting menu.press the OK button twice.
• This procedure shuts down the printer such that when you turn it on again,the language settings will have to be set.Select your option.

Hope this helps.Thanks!

hello,
If I may ask,which version of windows are you using?Vista,Xp,Windows7?They all have different modes of scanning.

Lets start with Vista:-

• See the window vista icon,click on that and then on all programs.
• Click on windows photo gallery.
• Click on file and select import from scanner option.
• Click import and then on scan.

windows Xp:-

• On the start menu,click on all programs.
• Move to accessories and then on to paint and click.
• Click on file and then select 'from scanner'
• You can set the changes you want and then click on scan.

Windows 7:-

• Click on the windows icon and then on to programs.
• Click on windows live photo gallery.
• Click on file and then 'import from scanner'
  
• Click import.
• You can set the changes you want and then click scan.
  

Hope this helps,please let me know by rating and commenting on it.Thanks alot!