20 Most Recent Boss Micro BR Digital Recorder - Page 6 Questions & Answers

You have to "mix" the tracks to create a final work before saving the file.

I had that problem too. What you need to check is the input level on the right side. Turn the wheel all the way up to 100 and the internal mic should be fine.

Try this link:http://www.rolandus.com/support/service_centers/ or this one:http://www.rolandus.com/support/?tab=service_repair I would recommend contacting Roland to make sure you are dealing with an authorized repair center especially if your unit is still under warranty.

Sounds like a version compatibility problem.

Check with the folks over at VSPLANET.com where Roland digital recorders are discussed in the forums.

There is special software to do this.

Visit

VSPLANET.com

where they discuss the Roland recorders in forums.

If you turn the power off between uses you will LIKELY have to resync the tracks. I doubt the unit remembers anything about sync to canned drum patterns once you turn the power off.

Try leaving it on and see if it acts the same.

Try this link:http://www.rolandus.com/products/productdetails.php?ProductId=818 Note the info under Power Supply,Current Draw and Expected Battery Life. Compare the specs to the results you are getting. Note that "The time may vary according to usage conditions, batteries used and type of SD memory card used." Here is a link to their support:http://www.rolandus.com/products/productdetails.php?ProductId=818&tab=downloads&skip=true If you didn't use the exact adapter recommended you may have damaged the circuitry and will have to have it serviced. It is definitely not something you can do yourself unless you have equipment to work on surface mount technology. The required adapter is listed in the info at the first link.

Generate a new audio file to record your project. If that does not work try to reboot your recorder. Also try an external mic.

Others have had problems doing so. I would get one specifically for the unit. One person got an adapter with an "S" suffix and that DID NOT WORK.

Get the exact replacement for this particular device as called for in your manual.

I would check the connector itself as the first thing to do. The connector jacks take a beating and sometimes do not contact well and just the capacitance of the nearby contacts is enough to make it appear to be working. IF you sense that high pitch goes through better, then this scenario is a possibility.

In any case, it sounds like it needs to go for repair.

Page 2 of the Turbostart manual explains that in some versions of Windows the Micro BR may appear as a removable storage device titled "Removable disk (?:)." The manual is here:http://cms.rolandus.com/assets/media/pdf/MICROBRts.pdf It also mentions free downloadable wave converter software. Hope this helps.

You may have damaged the data on the memory card. If you have no display at all carefully read page 125 of your manual.If it doesn't display with the adapter plugged in try new batteries. If it still doesn't display anything, contact the dealer you bought it from or try contacting Roland. This site should help:http://www.rolandus.com/support/service_centers/

Here is the link to their manuals:http://www.rolandus.com/products/productdetails.php?ProductId=818 Hope this helps.

Here is their support page:http://www.bossus.com/gear/productdetails.php?ProductId=753&tab=support&skip=true If the dealer you purchased it from can't help you have a look here for a dealer that can repair it:http://www.bossus.com/dealer_locator/ You are better off having something like this professionally repaired but before you do that check out the downloadable support documents to see if there is something you missed and if you don't want to contact their product support department by phone, email them. I've always had good luck with emailing companies as long as i carefully explained the problem. Hope this helps.

I am sure it can be repaired. Whenever ANY electronics get wet, IMMEDIATELY remove ANY pwer sources, including internal batteries.

If wetting was not pure water, flush unit with de-ionized water till absolutely clean of any residue. shake out all water and allow to dry a week before applying power.

Try this link:http://www.organservice.com/ Here's another one:http://www.combo-organ.com/Schematics/index.htm Join this one for free and post:http://organforum.com/forums/thread/73735.aspx This site is good too:http://www.combo-organ.com/spares_and_repairs.htm#Electrolytics Hope these help.

from reading instructions when you record channel 1 and 2 you are recordind channel 1 in stereo so you only recorded channel 1 try rcording on chanel 3 for vocal hope this helps

You can use it, but realize that you do all the work on the Micro BR and just download the result to the PC as an MP3 file. The PC treats the device just like a memory stick

make sure you save what you did, also make sure that it is finalized

Im Guessing Your Trying To Burn It Off Before Mastering It Which Means All The Tracks Between 1 And 10. First You Click Audio Cd Write/Play Then Select Disc At Once And Then It Should Guide You From There. I Hope This Helps
www.Myspace.com/CrossRoadsToNowhere2007