Top 20 Sony VPL-EX5 Projector Questions & Answers

Take the lamp cover back off. Check the mechanism that the projector uses to sense the door. It might be a small pressure switch. Check whatever triggers the mechanisms is still attached to the door and hasn't broken off.

Check for bulging capacitors on the power supply board. Replace if found.

replace the LCD panels (USD220) Have a good day! We supply original projector parts: lamp, bulb, Lcd panel, Lens, DMD chip, color wheel, motherboard, powersupply ... with high quality and competitive price. Jerry Lampdeng Limited Mobile: 0086-13178867858 Wechat ID: 008613178867858 Whatapp ID: 008613178867858 Skype: [email protected] http://www.lampdeng.com

initial password is enter,enter,enter,enter (enter four times)

Change the lamp.

HelloThe check the air filter. Clean it first. Turn the power OFF and unplug the device from AC mains. Draw out the air filter cover and remove it. Remove the air filter. Wash the air filter with mild dtergent solution and dry it in a shaded place. Attach the air filter back to device, so that it fits into the each claws on the air filter cover and replace the cover. If you neglect to clean the air filter, dust may accumulate, clogging it. As a result, temperature may arise inside the unit leading to a possible malfunction. Be sure to attach the aif filter cover firmly. "Power cannot be turned ON" if it is not closed securely.The air filter will have a face and a reverse side. Place the air filter, so that it fits on a notch on the air filter cover.If this doesn't help you, check the cooling fan. If fan speed is reduced, proper air circulation will not be ther, as a result the inside of the unit will overheat causing malfunctions, which has not been described anywhere in its manual. If needy, replace the fan. The final possible cause for this fault is with its Lamp itself. Confirm it before replacing, by doing all the above porcedure. OK.

try replacing the bul/lamp.

warning! $200 part http://www.amazon.com/Projector-LMP-E190-VPL-ES5-VPL-EX5-VPL-EX50/dp/B003ISW2KM

Remove the lamp and reseat it carefully, following the instructions in the user manual.


If this doesn't help you may find that you need a new lamp.. if you are in the UK you can purchase a Sony VPL-EX5 Lamp here or from here if you are in the USA

Its because of dust.Out bulb throw air to bulb and at projector through air blower or vacuum cleaner.You will get better result

change the resolution to 800x600 and if it works raise the resolution step by step

Question edited for a lot more clarity. Great Question. Press Menu Button for 10 seconds.

Data Projector

Projector Central https://www.projectorcentral.com > pdf > projecto... PDF Normal: Displays the image on the center position of the projected image without changing the resolution of the input signal or enlarging the image. VPL-DX270/ ... 54 pages

How to unlock control keys on sony projector? - Fixya

Fixya https://www.fixya.com > ... > Sony Sep 13, 2018 - To unlock the main panel keys, press the MENU button for 10 seconds. Read full answer. Aug 05, 2011 • Sony VPL-CS7 Multimedia Projector.

VPL-DX220

pro.sony https://pro.sony > ue_US > pdf > vpl-dx220 PDF Efficient, easy-to-use projector for classrooms and meeting rooms: with excellent picture quality and low ownership costs. The VPL-DX220 XGA projector is a ...

Sony VPL-DX220 3LCD Projector Specs

Projector Central https://www.projectorcentral.com > Sony-VPL-DX220 Sony VPL-DX220 Projector ; MSRP: $740 (USD) ; Resolution; 1024x768 ; Aspect Ratio; 4:3 (XGA) ; Contrast; 3,000:1 (full on/off) ; Color Processing; 8-bit. ‎Highlights · ‎Specifications · ‎Compare to Competition

See the following manuals. It will resolve your issue. VPL-EW5/EX50/EX5/ES5 (sony.com) VPL-EW5/EX50/EX5/ES5 (sony.com)

Question edited for a lot more clarity. You just take it to your local Sony Service Centre. This is a highly specialized printer and very expensive. There is help in this link https://www.google.com/search?q=sony+up-897md+doesn%27t+print ..

Take into your local Sony Service Centre for diagnosis and replace the switch.

I'm sorry, I'm not sure what you are asking for. Could you please provide more information or clarify your question?

The blinking red lamp/cover button on your Sony projector typically indicates an issue with the lamp or the projector's internal temperature. Here are a few steps you can take to try to resolve the issue:

1. Check the lamp cover: Make sure that the lamp cover is properly closed and secured. If the cover is not properly closed, the projector may not turn on or may turn off after a short time.
2. Check the lamp: If the lamp cover is properly closed, the next step is to check the lamp itself. Remove the lamp and check it for any visible signs of damage, such as cracks or discoloration. If the lamp appears to be in good condition, try reseating it to ensure it is properly installed. If you have access to a replacement lamp, try installing it to see if the problem is resolved.
3. Check the projector's air vents: Ensure that the projector's air vents are not blocked or obstructed, as this can cause the projector to overheat and shut down. Make sure that the projector is placed in a well-ventilated area.
4. Reset the projector: Try resetting the projector by turning it off and unplugging it from the power source for several minutes. Then, plug it back in and try turning it on again.
5. Consult the user manual: If none of the above steps solve the issue, consult the user manual for your Sony projector for further troubleshooting steps or contact Sony's customer support for further assistance.

If the issue persists, it may indicate a more serious internal problem with the projector that may require professional repair.

Yes, it is possible to get a replacement software disc for your Sony Handycam with Carl Zeiss lens. You can contact Sony Support to inquire about purchasing a replacement disc, or check if the software can be downloaded from their website. Alternatively, you can also check if a third-party seller has the disc available for purchase.

If your Sony projector (model VPL-EX145) has a light that is functioning properly but is not displaying any label information, there could be a few different issues causing the problem. Here are a few things you can try to troubleshoot the issue:

1. Check the projector's connections: Make sure the projector is properly connected to the computer or device that is sending the video signal, and that the connections are secure. If the projector is not properly connected or the connections are loose, it can cause the projector to display a blank screen.
2. Check the projector's settings: Make sure the projector's settings are properly configured for the type of video signal you are using. If the settings are not correctly configured, it can cause the projector to display a blank screen.
3. Check the source device: Make sure the device that is sending the video signal (such as a computer or DVD player) is functioning properly and that it is properly configured. If the device is not functioning properly or is not properly configured, it can cause the projector to display a blank screen.
4. Check for any other visible issues: Inspect the projector and its components for any visible issues that may be causing the problem. This can include debris or foreign objects that may have gotten stuck in the projector, or damage to the projector or its components.

If you have tried these troubleshooting steps and the problem persists, it may be necessary to have the projector serviced by a professional. A technician will be able to diagnose the problem and determine the necessary repairs.

Hi, Please turn off your device, clean the screen and power on the device before using it again. Otherwise, you might verify that you're using the device in an environment of moderate temperature. If still not working, then you might need to run a factory reset on the device. Thank you.

Try this Reset. If that doesn't work, you need a Sony Service Centre.

How to reset the CD changer to resolve disc playback problems.

https://www.sony.com > electronics > support > articles Turn off the CD player. Press the ALL CLEAR or CLEAR button, then press and hold down the POWER button on the CD player at the same ... SRAM parity errors are "soft errors" in the NIC SRAM induced by high-energy particles (e.g., solar flares) that can change the state of memory bits. It is a very common problem today with small-feature-size CMOS. These and other errors also occur in processors, cache memory, main memory, and IO buses.