Polycom VSX7000 Videoconferencing System (VSX-7000, VSX 7000, 7000) - Answered Questions & Fixed issues

Thank you

Check and replace damaged component/s at its horizontal scan output section circuit. Check the LOT (Line Output Transformer) too for damage. Replace the horizontal scan output transistor. Check the input voltage to LOT. If the voltage is absent check the feeder resistor; if any. If you wish to get some details; check the site linked here. Surf the site with patience. Pull up older posts. http://electronicshelponline.blogspot.com/

Pls can you ellaborate more on the problem...

There should be some loose solder terminals at its main power regulator section. Resolder all the suspected solder terminals there, by applying a little more solder. Check the solder terminals at the horizontal output stage too. The fault is with loose solder terminals itself.

It should say the IP network is up because you say it's on the network. Please clarify your second question?

You need to go into the audio settings via
Admin Settings
Audio Settings
and make sure Enable Polycom Microphone is checked off.
Reboot and see if your microphone is recognized.

If you asking for the manual option of ISDN and IP, then got to call preference and change the dialing method to auto

Constant red means it is set and ready to record messages after x amount of rings. Flashing red means you have a message. Please always include the model number is such questions and I can find you a manual. Polycom has lots! https://www.google.com/search?q=Polycom+phone+manual ..

try this on the manual: https://www.google.it/url?sa=t&rct=j&q=&esrc=s&source=web&cd=3&cad=rja&uact=8&ved=0CC4QFjAC&url=http%3A%2F%2Fsupport.polycom.com%2Fglobal%2Fdocuments%2Fsupport%2Fsetup_maintenance%2Fproducts%2Fvoice%2Fvortex_ef2280_programming_guide.pdf&ei=Z_j_VNXZH4vlaqq-gdAH&usg=AFQjCNGMJQMh4hSijpy9ic619NkkmlKOPA&bvm=bv.87611401,d.d2s

are you sure this feature is not blocked on your line? check with another phone connected to the same socket if you can dial the same numbers

hello This is not a dialing but trying to connect to the IP address setup in the system. Start editing the IP address giving the one that you would have already allocated to the device in the Router (i.e. 192.168.1.99) and then reboot it. It should connect then automatically. Best regards

The easiest way to fix this is to have use TFTPD32 and set the firmware in the default directory so that when the phone boots it gets its DHCP with Option 66 from the machine running TFTPD32 and automatically pulls the firmware

Unless you are good a solder then you probably won't be able to do it. You wolud need to solder a potentiometer inline of the + voltage to the speaker. Or solder one inline with the existing one. Potentiometer = voltage control aka volume control.

HI. sorry to hear that. Well, here's the solution
Settings should be changed, if it did not resolved the issue? check your coverage area and lastly go and seek a technician to have your device check and re evaluate the condition the mouthpiece or earpiece needs to be replace.
Please accept my solution..thanks

You power supply is probably defective

Has this been fixed yet?

http://www.brennanit.com.au/UserGuides/User%20Guide%20-%20Polycom%20Soundstation2.pdf

google speakerphone 210 manual for choices.

Question edited for clarity. Question moved from Video Consoles category. Trying to find a manual. Are you sure that model is correct? Eircom should give you a manual PDF. https://www.google.com/search?q=Eircom+perform+100+manual and https://www.google.com/search?q=Eircom+perform+100 ..

Good question but no 'make model (what it is). Base units have an antenna, make sure it is extended. Make sure the batteries in the satellite hand sets are good as they send out the signal to the base unit to be 'in range'. Not sure about the PIN request, refer to the manual. They are all online. Google make model manual ..