Yamaha RX-V463 Receiver - Answered Questions & Fixed issues

Your post indicates the use of a receiver. If you are in fact using a receiver, make sure you have a "video out" connection from the receiver to your television. Then make sure you have the correct input selection on the receiver, and on the TV.

Do not use HDMI thru your receiver. Go directly from the Cable box to the TV. Connect coaxial digital or optical to your receiver. Your receiver uses HDMI version 1.1 or 1.2, which is riddled with issues. If you want to read about them, Google HDMI Problems and you can read for hours. Long of the short of it is; Don't pass HDMI thru your receiver, use the receiver for audio only. Hope this answers the question. Sorry for the bad news! I'm in the industry and have been dealing with these issues for a couple years now.

Hello, Couldn't find PS WX-30 on the net or Samsung's site. Could you please confirm the model no.?

It is 30376. The trick to discovering, is to turn the receiver off, first. Then it will power on when you input mute/select 30376. Then you can program the DirecTV remote to adjust volume (in AV2 mode only or in all modes). However, it will only power up the receiver. It has to be turned off with the original remote or at the receiver itself.

check the speaker settings in the setup menu. The center channel may be turned off.

Look for universal remote with mute function. If not available you will have to purchase an original new remote.

I don't think you can. The rx-v463 doesn't have bluetooth capabilities

sounds like there is a problem in the amp. If you hold the "STRAIGHT" and "AUDIO SELECT" buttons and then press power, what does it say on the display? This will help narrow down where your problem may be.

this can be done by connecting individual wires to the input of choose eg left, centre ,rear right etc

To initialize and reboot the unit, hold down the Main Zone power button for more than 10 seconds. Hopefully this will allow you to turn on the unit.

First check the yam does play other sources of sound, e.g. radio or CD. Then try your ipod in another dock to check the Ipod is working. Then check the manual for the Yam to be sure that you have set it to a mode where it will take in the signal from the IPod. Did you switch it away from IPod source to play a DVD or a CD or the radio?

The problem can be the cable or speakers or RX-V463 or settings. Need to check one by one. Set the RX-V on DTS or Dolby Digital 1) Check Cables - connect the 2 (surround) cables from RXV's Centre Out to Centre speaker. If the Centre speaker works, then cables are ok. 2) Check speakers - Connect each Surround speaker to RXV's Centre out. If it works Speakers are ok. 3) Check RXV - Set it on DTS or Dolby Digital Connect RXV's surround out (one at a time) L and R to the Centre speaker. If there is no sound, the problem could be RXV's settings (I need to read the manual). Hope this helps.

Hi,possibly the laser is faulty in the unit.You need to send it to your repair agent for assessment.

Check the cabling and if all are fine go to speaker self test noise using remote to confirm your setup is fine. Thn finally check ur soundd feed format. Check which channels are nt working. Sound is always based on Content source.

seems like you have the jacks in the wrong place, try moving them around.

Are your speakers turn on? Look on the front panel and make sure it shows speakers A on the display. It is very easy to accidentally turn them off with the speakers front panel button.

maybe the audio amplifier IC's have problems that's why the device protects himself from a bigger damage

Power it On without speakers connected.If it powers up, reconnect speakers one at a time to find the cause.If the problem persist even without speakers connected, these unit needs servicing.if you have any more questions let us know.

dear sir you must press an audio solution 7ENHANCED you can do it by pressing audio mode in your remote

contact me for any further info

The remote has nothing to do with this.

Get into the manual. Page 14 says Component Video In will go to Component Video Out, not HDMI. No analog-digital video conversion is implied.