20 Most Recent
Yamaha HTR-6130 Receiver - Page 5 Questions & Answers
SAID CHECK UR SP CABLE?
Don't you mean it said, "Check SP wires"?
And what was the result when you did that?
How about if you disconnect all the speakers and try again. Then what? Add one at a time until it either fails again or starts working with all speakers attached.
Still fails with all speakers disconnected? Take it in to a shop.
Doesn't want to turn on
try to check the power supply chord or check the fuse, if fuse is busted try to replace it. if fuse is busted again there is a problem in its power supply, bring it to the nearest service center
Looking for remote control codes for my comcast
click this link and pick your flavor of remote you got and the manual for it will pop up and the codes are in there for you. Now this is the codes that are supported not somthing you wish to add if not supported and no fault of my own so please do not shoot the tech here.
please rate and leave feedback for your free solution today.
http://www.comcast.com/corporate/customers/customer_support/remotes.html
Btw, I’m available to help over the phone in case u need at
https://www.6ya.com/expert/edwy_1a56970cf1ea4620
Lights up no sound RX V 793
Hello Sir,
There is Still Light on Receiver.So you might be
"MUTE" function on your remote control has been ACTIVATED. The reason that you can still hear a very low sound is that the muting circuit within your stereo is not a full mute, but rather a -20dB mute.
- To Cancel or Deactivate the "MUTE" function, simply Press the "MUTE" button on your remote control.Try to Reduce Volume .If you have not or lost your remote control, you will have to purchase a new remote control unit.
Hope this Make you Better ..Thanks For Using FixYa....
How do I connect an external AM antenna
G'Day
The AM loop antenna needs to connect between the terminals marked as "AM ANT" and "GND" on the rear top right corner of the amp. This is the normal configuration for a loop antenna. The other option(not using a loop antenna) is to connect "GND" with a single insulated wire to a decent earth connection (2 m copper stake hammered into the ground or a water pipe, and a single wire elevated as long and as high as you can. this style of antenna system is not generally used these days, as the transmission power of radio stations has increased greatly over the years so that a small loop antenna will do the job So, most stations should be tunable with just the loop, remember however, that it will be directional. If the loop is in proximity to other electronic gear, it may not perform as well. Keep it as far away from the rest of your gear as you can.
You will generally get no AM stations AT ALL until you have connected the loop to both terminals. Happy to talk to you further about this. Please rate my solution. Cheers
regards
robotek
How to connect sony video camera to yamaha htr
How are you connecting the TV to the receiver? The receiver offers HDMI, component video and composite video outputs. The one you use will depend on what inputs are available on your TV. Whichever you choose, have the appropriate cables connected at both ends. Then make sure the proper source is selected on the TV and your camera output should be visible. The receiver manual is available for download at Yamaha's site if you need a copy for connection details.
Trying to get the sound
Your receiver probably doesn't support audio over HDMI - according to specs, it has just hdmi switching, but not hdmi repeating.
You have to connect PS3 via optical spdif cable to the receiver.
Yamaha HTR-6130
PS3
dish network DVR
Samsung 8500
I think you have to use actual a/v red and white cables. I don't think the component cables will work for the audio unless the receiver has the actual component jacks on it. use the red and white wires from a set of a/v cables instead of the component wires.
NO sound, display says CHECK SP cable?
Probably the speakers are not wired correctly. Check this by turning on the receiver without speakers connected. If the message is gone, issue was in the connection of speakers. Check that you have not short-wired the + and -.
No picture with Yamaha 6130 reciever. have
The TV must be tuned to the correct input also. Please cycle through the tv inputs by pressing the input button on the tv one time, then wait 5 to 10 seconds for the tv to recognize the input signal. If nothing, press again. You don't say which tv you have but many newer models have 5 to 7 input sources you will have to cycle through to find your signal.
With out more information, this is just one step in finding out what could be wrong. Please rank me accordingly.
Good luck.
Need to connect yamaha htr6130 receiver to an elan amplifier
Why don't we deal with the issues separately?
What are you trying to accomplish with speakers all around the house. Or did you mean around the ROOM?
You can't slave other amps off of this unit and have volume or source control at the receiver. It lacks any Preamp Outputs.
Tell us what you want to do, how things are connected (in detail) right now and maybe we can help you out.
It might also be helpful to know WHY you need to have multiple amps.
Not finding what you are looking for?