20 Most Recent Minolta bizhub 180 Black and White Copier - Page 7 Questions & Answers

explain the negative print?. But check the drum and or scanner have you run the F5 or F7? Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

That is a very old machine, try open closing front door does the screen display any codes? open front door upper left small access plate remove and push reset switch Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

http://onyxweb.mykonicaminolta.com/OneStopProductSupport?appMode=Public Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Check the charge Corona Assy unit for cyan (Blue) Open front covers Pull out mid section NOT paper section (have to unscrew two screw to open this section one to the left of the unit the other upper left just below the control panel. Should see four devices that look like they could be pulled out with your thumb. one each for each drum pull them out check that the very thin wire below the grid is not broken the re-seat each one check the all might as well. Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Well the code C-0211 is the bypass tray. Check that there is nothing near the lift section, remove the rear panel of the bypass tray check the connectors. Might have a bad sensor or clutch. As for trays one and two check for paper behind them!!! POWER OFF first and Remove the draw(s). If paper not picking up have tech come out and replace the rollers in each draw and the by pass tray. Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

check the phone line is it analog or digital if digital must be analog Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

replace the control panel Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Well the C0F35 is because there is no toner in the image unit so replace the image unit. just buy a whole new unit. as for the c0070 try this Power off the machine. Then remove the toner bottle, be careful the hole might be on the bottom and the toner is going to go everywhere. Then close the toner cover and turn on the machine. Let the machine go through it normal routine. When it asks for toner install the toner bottle correctly. If THE KNUB on the side of the bottle is damage put a new one in. That KNUB is what the toner motor uses to turn the bottle, if it damaged you get a code. If that does not work, you might have a bad motor or the home sensor or actuator for the toner bottle is bad worse case the control board is bad. Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

replace the drum and developer and clear required counters and conducted required procedures Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

sir as I said before replace the developer and the drum and conduct the proper F unctions and clear the proper counters Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

as i said before sir Replace the drum and developer and run the required F codes Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

sir as I said before Replace the drum and developer and run the required F codes Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

replace the drum and developer and run the required F codes Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Well you will need a tech because he will remove a chip which will be sent o Konica Minolta then on its way to the Secret Service!!!!!!!! to determine what was done in the mean time machine is DOWN until then no service tech can help until they get the blessing of the Secret Service counterfeiting of Money is a BIG NO NO! Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

sir, Does it copy only in black? does it print only in black, could be set to default to black what does the copier screen say if you touch reset button does do to color or black and white? Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

does it copy only in black? does it print only in black, could be set to default to black what does the copier screen say if you touch reset button does do to color or black and white? Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

what model machine and finisher unit? Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

replace the developer and the drum and run the required F codes F8, 7 and F5 clear the counters also Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f