20 Most Recent Minolta bizhub 180 Black and White Copier - Page 6 Questions & Answers

sir/Mam Which draw are you using ? Try a different one or the bypass tray. The rollers need to be replaced Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Are you using third party toner???? replace the black toner with OEM Konicaminolta toner Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Do you have the RU section also? which is use between the finisher and the copier. Mite also want to have a tech come out and update the firmware the copier OS. Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

mite want to have it cleaned. Have a tech look at it mite need to have the drum and developer replaced. Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

set the paper bypass tray to the size of the check mite need to be customize measure the checks and tell the copier the size its x and y size A4 is same as letter size except its for the rest of world USA is letter and the rest is A4. A3 is 11x17. Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Hello,

It's possible to be warn developer (i need to know how many copies are developer) or image unit is leaking. If i see a paper printed by the copier, i can do more accurate answer. You can call a service center.

Yes go to service mode and clear the counter. The counter is set up to replace the drum and developer. Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

https://printcopy.info/?l=en&mod=erc&brand=Konica-Minolta&model=bizhub%20C203&code=C2A04

hold clear/stop and power on the machine if the code comes back replace the fuser do not reset agian as the fuser can start a fire that will ruin a good day Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

sir/mam Power off the machine power on with the 2 and 5 depressed. Then go to soft switch set 3-1-1 if the code comes back its the fuser have a tech look at as it can start a fire ruining a perfectly good day Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Power off the machine power on with the 2 and 5 depressed. Then go to soft switch set 3-1-1 if the code comes back its the fuser have a tech look at as it can start a fire ruining a perfectly good day Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Mam, this is a very legacy machine! But, did you replace the developer??? Not the toner, you need to buy developer for this machine , before replacing the developer clear the counter in service mode, after replacing the developer you need to run the F8 procedure, adding toner is not going to help. After running F8 run F5 Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

https://printcopy.info/?l=en&mod=erc&brand=Konica-Minolta&model=bizhub%20240F&code=18 Konica Minolta bizhub 240F Error Codes Quoting from the web link shown above: Konica-Minolta bizhub 240F Error Codes

Exploded Views and Parts List Free!

Code

18

Description

Fuser Error (The number indicates the detailed error code) 0 The fuser did not become to the main motor driving temperature in 50 seconds after printing started. 1 The fuser did not become to the paper pick-up temperature in 50 seconds after printing started. 2 The fuser did not become to the main motor driving temperature in 30 seconds after warming up started. 3 The fuser did not become to the warm-up finishing temperature in 30 seconds after the motor started driving. 4 A temperature of 250°C or higher is detected in a mode other than sleep mode. 5 The fuser does not warm after fuser error is solved and the power is turned OFF/ON. 6 A low temperature of 10°C is detected in 10 seconds after printing started. 7 A temperature of 190°C is detected in ready mode after printing finished.

Remedy

1. Turn on the power again, and verify the fuser warms up. If it does not, see step 4. 2. Check the contact between Fusing thermistor and Connect A PCB(P89). 3. Check the contact between Connect A PCB (P80C) and the main board. 4. Replace the Fuser. 5. After replacing the Fuser, verify the fuser warms up when the power is on. 6. Replace the main control PCB.

You dont adjust the TCR it is developer to Toner ratio. Inside the developer unit. You replace the developer if required Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Clean the sensors under the transfer belt, the black drum recommended be replaced. Since Black is what all the colors are aligned to. To clean sensor requires removal of the Transfer belt be careful as any damage to the belt will result in copy quality issues Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

FIRST, if this code comes back. Have a technician look at it DO NOT CONTINUE TO RESET the code!!!! AS this is for the Hot Part called the FUSER. It can catch on fire! And that will ruin a perfectly good day!!!! Open the front door of the copier, copier must be on. Look to your upper left, you should see a small cover with a screw remove and the cover. Inside you will see a small button, press it that should reset the copier. AGAIN if this code comes back. Have a technician look at it DO NOT CONTINUE TO RESET the code!!!! AS this is for the Hot Part called the FUSER. It can catch on fire! And that will ruin a perfectly good day!!!! Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Remove the drum unit and clean all contacts on the rear of the unit and inside the machine where they would contact. you mite also want to replace the drum unit (worse case the HV(High Voltage) and or the Main board are bad), when was the developer and drum changed. Quite a legacy machine!!!!!!!!. Was built before Minolta and Konica became one!!!! Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

missing number in the error code it will be c-XXXX Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f